Commit bd7ec70c authored by Raymond Knopp's avatar Raymond Knopp

changes from fourmi

parent ee1d0d56
......@@ -305,11 +305,11 @@ int trx_usrp_stop(int card) {
rx_gain_calib_table_t calib_table_b210[] = {
{3500000000.0,47.0},
{2660000000.0,53.0},
{2300000000.0,54.0},
{1880000000.0,55.0},
{816000000.0,62.0},
{3500000000.0,44.0},
{2660000000.0,49.0},
{2300000000.0,50.0},
{1880000000.0,53.0},
{816000000.0,58.0},
{-1,0}};
rx_gain_calib_table_t calib_table_b210_38[] = {
......@@ -507,7 +507,7 @@ int openair0_dev_init_usrp(openair0_device* device, openair0_config_t *openair0_
case 30720000:
s->usrp->set_master_clock_rate(30.72e6);
// from usrp_time_offset
openair0_cfg[0].samples_per_packet = 2048;
openair0_cfg[0].samples_per_packet = 4096;
openair0_cfg[0].tx_sample_advance = 115;
openair0_cfg[0].tx_bw = 20e6;
openair0_cfg[0].rx_bw = 20e6;
......
......@@ -36,7 +36,7 @@ eNBs =
nb_antennas_tx = 1;
nb_antennas_rx = 1;
tx_gain = 90;
rx_gain = 130;
rx_gain = 125;
prach_root = 0;
prach_config_index = 0;
prach_high_speed = "DISABLE";
......@@ -140,10 +140,10 @@ eNBs =
NETWORK_INTERFACES :
{
ENB_INTERFACE_NAME_FOR_S1_MME = "eth0";
ENB_IPV4_ADDRESS_FOR_S1_MME = "192.168.12.213/24";
ENB_IPV4_ADDRESS_FOR_S1_MME = "192.168.12.212/24";
ENB_INTERFACE_NAME_FOR_S1U = "eth0";
ENB_IPV4_ADDRESS_FOR_S1U = "192.168.12.213/24";
ENB_IPV4_ADDRESS_FOR_S1U = "192.168.12.212/24";
ENB_PORT_FOR_S1U = 2152; # Spec 2152
};
......
......@@ -36,7 +36,7 @@ eNBs =
nb_antennas_tx = 1;
nb_antennas_rx = 1;
tx_gain = 90;
rx_gain = 132;
rx_gain = 125;
prach_root = 0;
prach_config_index = 0;
prach_high_speed = "DISABLE";
......@@ -143,10 +143,10 @@ eNBs =
NETWORK_INTERFACES :
{
ENB_INTERFACE_NAME_FOR_S1_MME = "eth0";
ENB_IPV4_ADDRESS_FOR_S1_MME = "192.168.12.213/24";
ENB_IPV4_ADDRESS_FOR_S1_MME = "192.168.12.212/24";
ENB_INTERFACE_NAME_FOR_S1U = "eth0";
ENB_IPV4_ADDRESS_FOR_S1U = "192.168.12.213/24";
ENB_IPV4_ADDRESS_FOR_S1U = "192.168.12.212/24";
ENB_PORT_FOR_S1U = 2152; # Spec 2152
};
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment