Commit f66f6e49 authored by Cedric Roux's avatar Cedric Roux

deal with empty subframes at UE side even in oaisim

The memset was also too big. It should only clear
one subframe.

Only tested without abstraction.
Abstraction does not work for the moment anyway, but just to
keep that in mind.
parent b904ce79
......@@ -986,8 +986,8 @@ void ulsch_common_procedures(PHY_VARS_UE *ue, UE_rxtx_proc_t *proc, uint8_t empt
int subframe_tx = proc->subframe_tx;
int frame_tx = proc->frame_tx;
int ulsch_start;
#if defined(EXMIMO) || defined(OAI_USRP) || defined(OAI_BLADERF) || defined(OAI_LMSSDR)
int overflow=0;
#if defined(EXMIMO) || defined(OAI_USRP) || defined(OAI_BLADERF) || defined(OAI_LMSSDR)
int k,l;
int dummy_tx_buffer[3840*4] __attribute__((aligned(16)));
#endif
......@@ -1015,14 +1015,15 @@ void ulsch_common_procedures(PHY_VARS_UE *ue, UE_rxtx_proc_t *proc, uint8_t empt
ulsch_start = (frame_parms->samples_per_tti*subframe_tx)-ue->N_TA_offset; //-ue->timing_advance;
#endif //else EXMIMO
#if defined(EXMIMO) || defined(OAI_USRP) || defined(OAI_BLADERF) || defined(OAI_LMSSDR)
//#if defined(EXMIMO) || defined(OAI_USRP) || defined(OAI_BLADERF) || defined(OAI_LMSSDR)
if (empty_subframe)
{
//#if 1
overflow = ulsch_start - 9*frame_parms->samples_per_tti;
for (aa=0; aa<frame_parms->nb_antennas_tx; aa++) {
memset(&ue->common_vars.txdata[aa][ulsch_start],0,4*cmin(frame_parms->samples_per_tti*LTE_NUMBER_OF_SUBFRAMES_PER_FRAME,ulsch_start+frame_parms->samples_per_tti));
//memset(&ue->common_vars.txdata[aa][ulsch_start],0,4*cmin(frame_parms->samples_per_tti*LTE_NUMBER_OF_SUBFRAMES_PER_FRAME,ulsch_start+frame_parms->samples_per_tti));
memset(&ue->common_vars.txdata[aa][ulsch_start],0,4*cmin(frame_parms->samples_per_tti-overflow,frame_parms->samples_per_tti));
if (overflow> 0)
memset(&ue->common_vars.txdata[aa][0],0,4*overflow);
......@@ -1043,7 +1044,7 @@ void ulsch_common_procedures(PHY_VARS_UE *ue, UE_rxtx_proc_t *proc, uint8_t empt
#endif*/
return;
}
#endif
//#endif
if ((frame_tx%100) == 0)
LOG_D(PHY,"[UE %d] Frame %d, subframe %d: ulsch_start = %d (rxoff %d, HW TA %d, timing advance %d, TA_offset %d\n",
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment