Commit 6548841d authored by knopp's avatar knopp

git-svn-id: http://svn.eurecom.fr/openair4G/trunk@7553 818b1a75-f10b-46b9-bf7c-635c3b92a50f

parent 01600794
......@@ -19,7 +19,7 @@ eNBs =
mobile_country_code = "208";
mobile_network_code = "92";
mobile_network_code = "93";
////////// Physical parameters:
......@@ -30,7 +30,7 @@ eNBs =
tdd_config_s = 0;
prefix_type = "NORMAL";
eutra_band = 7;
downlink_frequency = 2660000000L;
downlink_frequency = 2680000000L;
uplink_frequency_offset = -120000000;
Nid_cell = 0;
N_RB_DL = 25;
......@@ -125,7 +125,7 @@ eNBs =
}
////////// MME parameters:
mme_ip_address = ( { ipv4 = "192.168.13.11";
mme_ip_address = ( { ipv4 = "192.168.12.171";
ipv6 = "192:168:30::17";
active = "yes";
preference = "ipv4";
......@@ -135,10 +135,10 @@ eNBs =
NETWORK_INTERFACES :
{
ENB_INTERFACE_NAME_FOR_S1_MME = "eth0";
ENB_IPV4_ADDRESS_FOR_S1_MME = "192.168.13.10/24";
ENB_IPV4_ADDRESS_FOR_S1_MME = "192.168.12.213/24";
ENB_INTERFACE_NAME_FOR_S1U = "eth0";
ENB_IPV4_ADDRESS_FOR_S1U = "192.168.13.10/24";
ENB_IPV4_ADDRESS_FOR_S1U = "192.168.12.213/24";
ENB_PORT_FOR_S1U = 2152; # Spec 2152
};
......
......@@ -38,7 +38,7 @@ eNBs =
nb_antennas_tx = 2;
nb_antennas_rx = 2;
tx_gain = 90;
rx_gain = 135;
rx_gain = 115;
prach_root = 0;
prach_config_index = 0;
prach_high_speed = "DISABLE";
......
......@@ -1193,6 +1193,8 @@ static void* eNB_thread_rx( void* param )
FILE *rx_time_file;
char rx_time_name[101];
int i;
if (opp_enabled == 1){
snprintf(rx_time_name, 100,"/tmp/%s_rx_time_thread_sf_%d", "eNB", proc->subframe);
rx_time_file = fopen(rx_time_name,"w");
......@@ -1280,11 +1282,7 @@ static void* eNB_thread_rx( void* param )
if ((((PHY_vars_eNB_g[0][proc->CC_id]->lte_frame_parms.frame_type == TDD )&&(subframe_select(&PHY_vars_eNB_g[0][proc->CC_id]->lte_frame_parms,proc->subframe_rx)==SF_UL)) ||
(PHY_vars_eNB_g[0][proc->CC_id]->lte_frame_parms.frame_type == FDD))) {
#ifdef OAI_USRP
for (i=0;i<PHY_vars_eNB_g[0][proc->CC_id]->lte_frame_parms.nb_antennas_rx;i++)
rescale(&PHY_vars_eNB_g[0][proc->CC_id]->lte_eNB_common_vars.rxdata[0][i][proc->subframe_rx*phy_vars_eNB->lte_frame_parms.samples_per_tti],
phy_vars_eNB->lte_frame_parms.samples_per_tti);
#endif
phy_procedures_eNB_RX( proc->subframe, PHY_vars_eNB_g[0][proc->CC_id], 0, no_relay );
}
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment