pata_opti.c 5.22 KB
Newer Older
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
/*
 * pata_opti.c 	- ATI PATA for new ATA layer
 *			  (C) 2005 Red Hat Inc
 *
 * Based on
 *  linux/drivers/ide/pci/opti621.c		Version 0.7	Sept 10, 2002
 *
 *  Copyright (C) 1996-1998  Linus Torvalds & authors (see below)
 *
 * Authors:
 * Jaromir Koutek <miri@punknet.cz>,
 * Jan Harkes <jaharkes@cwi.nl>,
 * Mark Lord <mlord@pobox.com>
 * Some parts of code are from ali14xx.c and from rz1000.c.
 *
 * Also consulted the FreeBSD prototype driver by Kevin Day to try
 * and resolve some confusions. Further documentation can be found in
 * Ralf Brown's interrupt list
 *
 * If you have other variants of the Opti range (Viper/Vendetta) please
 * try this driver with those PCI idents and report back. For the later
 * chips see the pata_optidma driver
 *
 */

#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>

#define DRV_NAME "pata_opti"
36
#define DRV_VERSION "0.2.9"
37 38 39 40 41 42 43 44 45 46 47

enum {
	READ_REG	= 0,	/* index of Read cycle timing register */
	WRITE_REG 	= 1,	/* index of Write cycle timing register */
	CNTRL_REG 	= 3,	/* index of Control register */
	STRAP_REG 	= 5,	/* index of Strap register */
	MISC_REG 	= 6	/* index of Miscellaneous register */
};

/**
 *	opti_pre_reset		-	probe begin
Tejun Heo's avatar
Tejun Heo committed
48
 *	@link: ATA link
49
 *	@deadline: deadline jiffies for the operation
50 51 52 53
 *
 *	Set up cable type and use generic probe init
 */

Tejun Heo's avatar
Tejun Heo committed
54
static int opti_pre_reset(struct ata_link *link, unsigned long deadline)
55
{
Tejun Heo's avatar
Tejun Heo committed
56
	struct ata_port *ap = link->ap;
57 58 59 60 61 62
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	static const struct pci_bits opti_enable_bits[] = {
		{ 0x45, 1, 0x80, 0x00 },
		{ 0x40, 1, 0x08, 0x00 }
	};

63 64
	if (!pci_test_config_bits(pdev, &opti_enable_bits[ap->port_no]))
		return -ENOENT;
65

Tejun Heo's avatar
Tejun Heo committed
66
	return ata_sff_prereset(link, deadline);
67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82
}

/**
 *	opti_write_reg		-	control register setup
 *	@ap: ATA port
 *	@value: value
 *	@reg: control register number
 *
 *	The Opti uses magic 'trapdoor' register accesses to do configuration
 *	rather than using PCI space as other controllers do. The double inw
 *	on the error register activates configuration mode. We can then write
 *	the control register
 */

static void opti_write_reg(struct ata_port *ap, u8 val, int reg)
{
Tejun Heo's avatar
Tejun Heo committed
83
	void __iomem *regio = ap->ioaddr.cmd_addr;
84 85

	/* These 3 unlock the control register access */
Tejun Heo's avatar
Tejun Heo committed
86 87 88
	ioread16(regio + 1);
	ioread16(regio + 1);
	iowrite8(3, regio + 2);
89 90

	/* Do the I/O */
Tejun Heo's avatar
Tejun Heo committed
91
	iowrite8(val, regio + reg);
92 93

	/* Relock */
Tejun Heo's avatar
Tejun Heo committed
94
	iowrite8(0x83, regio + 2);
95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111
}

/**
 *	opti_set_piomode	-	set initial PIO mode data
 *	@ap: ATA interface
 *	@adev: ATA device
 *
 *	Called to do the PIO mode setup. Timing numbers are taken from
 *	the FreeBSD driver then pre computed to keep the code clean. There
 *	are two tables depending on the hardware clock speed.
 */

static void opti_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
	struct ata_device *pair = ata_dev_pair(adev);
	int clock;
	int pio = adev->pio_mode - XFER_PIO_0;
Tejun Heo's avatar
Tejun Heo committed
112
	void __iomem *regio = ap->ioaddr.cmd_addr;
113 114 115 116 117 118 119 120 121 122 123 124
	u8 addr;

	/* Address table precomputed with prefetch off and a DCLK of 2 */
	static const u8 addr_timing[2][5] = {
		{ 0x30, 0x20, 0x20, 0x10, 0x10 },
		{ 0x20, 0x20, 0x10, 0x10, 0x10 }
	};
	static const u8 data_rec_timing[2][5] = {
		{ 0x6B, 0x56, 0x42, 0x32, 0x31 },
		{ 0x58, 0x44, 0x32, 0x22, 0x21 }
	};

Tejun Heo's avatar
Tejun Heo committed
125 126
	iowrite8(0xff, regio + 5);
	clock = ioread16(regio + 5) & 1;
127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151

	/*
 	 *	As with many controllers the address setup time is shared
 	 *	and must suit both devices if present.
	 */

	addr = addr_timing[clock][pio];
	if (pair) {
		/* Hardware constraint */
		u8 pair_addr = addr_timing[clock][pair->pio_mode - XFER_PIO_0];
		if (pair_addr > addr)
			addr = pair_addr;
	}

	/* Commence primary programming sequence */
	opti_write_reg(ap, adev->devno, MISC_REG);
	opti_write_reg(ap, data_rec_timing[clock][pio], READ_REG);
	opti_write_reg(ap, data_rec_timing[clock][pio], WRITE_REG);
	opti_write_reg(ap, addr, MISC_REG);

	/* Programming sequence complete, override strapping */
	opti_write_reg(ap, 0x85, CNTRL_REG);
}

static struct scsi_host_template opti_sht = {
152
	ATA_PIO_SHT(DRV_NAME),
153 154 155
};

static struct ata_port_operations opti_port_ops = {
156 157
	.inherits	= &ata_sff_port_ops,
	.cable_detect	= ata_cable_40wire,
158
	.set_piomode	= opti_set_piomode,
159
	.prereset	= opti_pre_reset,
160 161 162 163
};

static int opti_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
164
	static const struct ata_port_info info = {
165
		.flags = ATA_FLAG_SLAVE_POSS,
166
		.pio_mask = ATA_PIO4,
167 168
		.port_ops = &opti_port_ops
	};
169
	const struct ata_port_info *ppi[] = { &info, NULL };
170

171
	ata_print_version_once(&dev->dev, DRV_VERSION);
172

173
	return ata_pci_sff_init_one(dev, ppi, &opti_sht, NULL, 0);
174 175 176
}

static const struct pci_device_id opti[] = {
177 178 179 180
	{ PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C621), 0 },
	{ PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C825), 1 },

	{ },
181 182 183
};

static struct pci_driver opti_pci_driver = {
184
	.name 		= DRV_NAME,
185 186
	.id_table	= opti,
	.probe 		= opti_init_one,
187
	.remove		= ata_pci_remove_one,
188
#ifdef CONFIG_PM
189 190
	.suspend	= ata_pci_device_suspend,
	.resume		= ata_pci_device_resume,
191
#endif
192 193
};

Axel Lin's avatar
Axel Lin committed
194
module_pci_driver(opti_pci_driver);
195 196 197 198 199 200

MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Opti 621/621X");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, opti);
MODULE_VERSION(DRV_VERSION);