ssu100.c 17.1 KB
Newer Older
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
/*
 * usb-serial driver for Quatech SSU-100
 *
 * based on ftdi_sio.c and the original serqt_usb.c from Quatech
 *
 */

#include <linux/errno.h>
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/tty.h>
#include <linux/tty_driver.h>
#include <linux/tty_flip.h>
#include <linux/module.h>
#include <linux/serial.h>
#include <linux/usb.h>
#include <linux/usb/serial.h>
18
#include <linux/serial_reg.h>
19 20 21 22 23 24 25 26 27 28 29 30 31 32
#include <linux/uaccess.h>

#define QT_OPEN_CLOSE_CHANNEL       0xca
#define QT_SET_GET_DEVICE           0xc2
#define QT_SET_GET_REGISTER         0xc0
#define QT_GET_SET_PREBUF_TRIG_LVL  0xcc
#define QT_SET_ATF                  0xcd
#define QT_GET_SET_UART             0xc1
#define QT_TRANSFER_IN              0xc0
#define QT_HW_FLOW_CONTROL_MASK     0xc5
#define QT_SW_FLOW_CONTROL_MASK     0xc6

#define  SERIAL_MSR_MASK            0xf0

33
#define  SERIAL_CRTSCTS ((UART_MCR_RTS << 8) | UART_MSR_CTS)
34

35
#define  SERIAL_EVEN_PARITY         (UART_LCR_PARITY | UART_LCR_EPAR)
36 37 38 39 40 41 42 43 44 45 46 47 48

#define  MAX_BAUD_RATE              460800

#define ATC_DISABLED                0x00
#define DUPMODE_BITS        0xc0
#define RR_BITS             0x03
#define LOOPMODE_BITS       0x41
#define RS232_MODE          0x00
#define RTSCTS_TO_CONNECTOR 0x40
#define CLKS_X4             0x02
#define FULLPWRBIT          0x00000080
#define NEXT_BOARD_POWER_BIT        0x00000004

49
static bool debug;
50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77

/* Version Information */
#define DRIVER_VERSION "v0.1"
#define DRIVER_DESC "Quatech SSU-100 USB to Serial Driver"

#define	USB_VENDOR_ID_QUATECH	0x061d	/* Quatech VID */
#define QUATECH_SSU100	0xC020	/* SSU100 */

static const struct usb_device_id id_table[] = {
	{USB_DEVICE(USB_VENDOR_ID_QUATECH, QUATECH_SSU100)},
	{}			/* Terminating entry */
};

MODULE_DEVICE_TABLE(usb, id_table);


static struct usb_driver ssu100_driver = {
	.name			       = "ssu100",
	.probe			       = usb_serial_probe,
	.disconnect		       = usb_serial_disconnect,
	.id_table		       = id_table,
	.suspend		       = usb_serial_suspend,
	.resume			       = usb_serial_resume,
	.no_dynamic_id		       = 1,
	.supports_autosuspend	       = 1,
};

struct ssu100_port_private {
78
	spinlock_t status_lock;
79 80 81
	u8 shadowLSR;
	u8 shadowMSR;
	wait_queue_head_t delta_msr_wait; /* Used for TIOCMIWAIT */
82
	struct async_icount icount;
83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129
};

static void ssu100_release(struct usb_serial *serial)
{
	struct ssu100_port_private *priv = usb_get_serial_port_data(*serial->port);

	dbg("%s", __func__);
	kfree(priv);
}

static inline int ssu100_control_msg(struct usb_device *dev,
				     u8 request, u16 data, u16 index)
{
	return usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
			       request, 0x40, data, index,
			       NULL, 0, 300);
}

static inline int ssu100_setdevice(struct usb_device *dev, u8 *data)
{
	u16 x = ((u16)(data[1] << 8) | (u16)(data[0]));

	return ssu100_control_msg(dev, QT_SET_GET_DEVICE, x, 0);
}


static inline int ssu100_getdevice(struct usb_device *dev, u8 *data)
{
	return usb_control_msg(dev, usb_rcvctrlpipe(dev, 0),
			       QT_SET_GET_DEVICE, 0xc0, 0, 0,
			       data, 3, 300);
}

static inline int ssu100_getregister(struct usb_device *dev,
				     unsigned short uart,
				     unsigned short reg,
				     u8 *data)
{
	return usb_control_msg(dev, usb_rcvctrlpipe(dev, 0),
			       QT_SET_GET_REGISTER, 0xc0, reg,
			       uart, data, sizeof(*data), 300);

}


static inline int ssu100_setregister(struct usb_device *dev,
				     unsigned short uart,
130
				     unsigned short reg,
131 132
				     u16 data)
{
133
	u16 value = (data << 8) | reg;
134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158

	return usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
			       QT_SET_GET_REGISTER, 0x40, value, uart,
			       NULL, 0, 300);

}

#define set_mctrl(dev, set)		update_mctrl((dev), (set), 0)
#define clear_mctrl(dev, clear)	update_mctrl((dev), 0, (clear))

/* these do not deal with device that have more than 1 port */
static inline int update_mctrl(struct usb_device *dev, unsigned int set,
			       unsigned int clear)
{
	unsigned urb_value;
	int result;

	if (((set | clear) & (TIOCM_DTR | TIOCM_RTS)) == 0) {
		dbg("%s - DTR|RTS not being set|cleared", __func__);
		return 0;	/* no change */
	}

	clear &= ~set;	/* 'set' takes precedence over 'clear' */
	urb_value = 0;
	if (set & TIOCM_DTR)
159
		urb_value |= UART_MCR_DTR;
160
	if (set & TIOCM_RTS)
161
		urb_value |= UART_MCR_RTS;
162

163
	result = ssu100_setregister(dev, 0, UART_MCR, urb_value);
164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244
	if (result < 0)
		dbg("%s Error from MODEM_CTRL urb", __func__);

	return result;
}

static int ssu100_initdevice(struct usb_device *dev)
{
	u8 *data;
	int result = 0;

	dbg("%s", __func__);

	data = kzalloc(3, GFP_KERNEL);
	if (!data)
		return -ENOMEM;

	result = ssu100_getdevice(dev, data);
	if (result < 0) {
		dbg("%s - get_device failed %i", __func__, result);
		goto out;
	}

	data[1] &= ~FULLPWRBIT;

	result = ssu100_setdevice(dev, data);
	if (result < 0) {
		dbg("%s - setdevice failed %i", __func__, result);
		goto out;
	}

	result = ssu100_control_msg(dev, QT_GET_SET_PREBUF_TRIG_LVL, 128, 0);
	if (result < 0) {
		dbg("%s - set prebuffer level failed %i", __func__, result);
		goto out;
	}

	result = ssu100_control_msg(dev, QT_SET_ATF, ATC_DISABLED, 0);
	if (result < 0) {
		dbg("%s - set ATFprebuffer level failed %i", __func__, result);
		goto out;
	}

	result = ssu100_getdevice(dev, data);
	if (result < 0) {
		dbg("%s - get_device failed %i", __func__, result);
		goto out;
	}

	data[0] &= ~(RR_BITS | DUPMODE_BITS);
	data[0] |= CLKS_X4;
	data[1] &= ~(LOOPMODE_BITS);
	data[1] |= RS232_MODE;

	result = ssu100_setdevice(dev, data);
	if (result < 0) {
		dbg("%s - setdevice failed %i", __func__, result);
		goto out;
	}

out:	kfree(data);
	return result;

}


static void ssu100_set_termios(struct tty_struct *tty,
			       struct usb_serial_port *port,
			       struct ktermios *old_termios)
{
	struct usb_device *dev = port->serial->dev;
	struct ktermios *termios = tty->termios;
	u16 baud, divisor, remainder;
	unsigned int cflag = termios->c_cflag;
	u16 urb_value = 0; /* will hold the new flags */
	int result;

	dbg("%s", __func__);

	if (cflag & PARENB) {
		if (cflag & PARODD)
245
			urb_value |= UART_LCR_PARITY;
246 247 248 249 250 251
		else
			urb_value |= SERIAL_EVEN_PARITY;
	}

	switch (cflag & CSIZE) {
	case CS5:
252
		urb_value |= UART_LCR_WLEN5;
253 254
		break;
	case CS6:
255
		urb_value |= UART_LCR_WLEN6;
256 257
		break;
	case CS7:
258
		urb_value |= UART_LCR_WLEN7;
259 260 261
		break;
	default:
	case CS8:
262
		urb_value |= UART_LCR_WLEN8;
263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313
		break;
	}

	baud = tty_get_baud_rate(tty);
	if (!baud)
		baud = 9600;

	dbg("%s - got baud = %d\n", __func__, baud);


	divisor = MAX_BAUD_RATE / baud;
	remainder = MAX_BAUD_RATE % baud;
	if (((remainder * 2) >= baud) && (baud != 110))
		divisor++;

	urb_value = urb_value << 8;

	result = ssu100_control_msg(dev, QT_GET_SET_UART, divisor, urb_value);
	if (result < 0)
		dbg("%s - set uart failed", __func__);

	if (cflag & CRTSCTS)
		result = ssu100_control_msg(dev, QT_HW_FLOW_CONTROL_MASK,
					    SERIAL_CRTSCTS, 0);
	else
		result = ssu100_control_msg(dev, QT_HW_FLOW_CONTROL_MASK,
					    0, 0);
	if (result < 0)
		dbg("%s - set HW flow control failed", __func__);

	if (I_IXOFF(tty) || I_IXON(tty)) {
		u16 x = ((u16)(START_CHAR(tty) << 8) | (u16)(STOP_CHAR(tty)));

		result = ssu100_control_msg(dev, QT_SW_FLOW_CONTROL_MASK,
					    x, 0);
	} else
		result = ssu100_control_msg(dev, QT_SW_FLOW_CONTROL_MASK,
					    0, 0);

	if (result < 0)
		dbg("%s - set SW flow control failed", __func__);

}


static int ssu100_open(struct tty_struct *tty, struct usb_serial_port *port)
{
	struct usb_device *dev = port->serial->dev;
	struct ssu100_port_private *priv = usb_get_serial_port_data(port);
	u8 *data;
	int result;
314
	unsigned long flags;
315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331

	dbg("%s - port %d", __func__, port->number);

	data = kzalloc(2, GFP_KERNEL);
	if (!data)
		return -ENOMEM;

	result = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0),
				 QT_OPEN_CLOSE_CHANNEL,
				 QT_TRANSFER_IN, 0x01,
				 0, data, 2, 300);
	if (result < 0) {
		dbg("%s - open failed %i", __func__, result);
		kfree(data);
		return result;
	}

332
	spin_lock_irqsave(&priv->status_lock, flags);
333 334
	priv->shadowLSR = data[0];
	priv->shadowMSR = data[1];
335
	spin_unlock_irqrestore(&priv->status_lock, flags);
336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378

	kfree(data);

/* set to 9600 */
	result = ssu100_control_msg(dev, QT_GET_SET_UART, 0x30, 0x0300);
	if (result < 0)
		dbg("%s - set uart failed", __func__);

	if (tty)
		ssu100_set_termios(tty, port, tty->termios);

	return usb_serial_generic_open(tty, port);
}

static void ssu100_close(struct usb_serial_port *port)
{
	dbg("%s", __func__);
	usb_serial_generic_close(port);
}

static int get_serial_info(struct usb_serial_port *port,
			   struct serial_struct __user *retinfo)
{
	struct serial_struct tmp;

	if (!retinfo)
		return -EFAULT;

	memset(&tmp, 0, sizeof(tmp));
	tmp.line		= port->serial->minor;
	tmp.port		= 0;
	tmp.irq			= 0;
	tmp.flags		= ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ;
	tmp.xmit_fifo_size	= port->bulk_out_size;
	tmp.baud_base		= 9600;
	tmp.close_delay		= 5*HZ;
	tmp.closing_wait	= 30*HZ;

	if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
		return -EFAULT;
	return 0;
}

379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417
static int wait_modem_info(struct usb_serial_port *port, unsigned int arg)
{
	struct ssu100_port_private *priv = usb_get_serial_port_data(port);
	struct async_icount prev, cur;
	unsigned long flags;

	spin_lock_irqsave(&priv->status_lock, flags);
	prev = priv->icount;
	spin_unlock_irqrestore(&priv->status_lock, flags);

	while (1) {
		wait_event_interruptible(priv->delta_msr_wait,
					 ((priv->icount.rng != prev.rng) ||
					  (priv->icount.dsr != prev.dsr) ||
					  (priv->icount.dcd != prev.dcd) ||
					  (priv->icount.cts != prev.cts)));

		if (signal_pending(current))
			return -ERESTARTSYS;

		spin_lock_irqsave(&priv->status_lock, flags);
		cur = priv->icount;
		spin_unlock_irqrestore(&priv->status_lock, flags);

		if ((prev.rng == cur.rng) &&
		    (prev.dsr == cur.dsr) &&
		    (prev.dcd == cur.dcd) &&
		    (prev.cts == cur.cts))
			return -EIO;

		if ((arg & TIOCM_RNG && (prev.rng != cur.rng)) ||
		    (arg & TIOCM_DSR && (prev.dsr != cur.dsr)) ||
		    (arg & TIOCM_CD  && (prev.dcd != cur.dcd)) ||
		    (arg & TIOCM_CTS && (prev.cts != cur.cts)))
			return 0;
	}
	return 0;
}

418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441
static int ssu100_get_icount(struct tty_struct *tty,
			struct serial_icounter_struct *icount)
{
	struct usb_serial_port *port = tty->driver_data;
	struct ssu100_port_private *priv = usb_get_serial_port_data(port);
	struct async_icount cnow = priv->icount;

	icount->cts = cnow.cts;
	icount->dsr = cnow.dsr;
	icount->rng = cnow.rng;
	icount->dcd = cnow.dcd;
	icount->rx = cnow.rx;
	icount->tx = cnow.tx;
	icount->frame = cnow.frame;
	icount->overrun = cnow.overrun;
	icount->parity = cnow.parity;
	icount->brk = cnow.brk;
	icount->buf_overrun = cnow.buf_overrun;

	return 0;
}



442
static int ssu100_ioctl(struct tty_struct *tty,
443 444 445 446 447 448 449 450 451 452 453 454
		    unsigned int cmd, unsigned long arg)
{
	struct usb_serial_port *port = tty->driver_data;

	dbg("%s cmd 0x%04x", __func__, cmd);

	switch (cmd) {
	case TIOCGSERIAL:
		return get_serial_info(port,
				       (struct serial_struct __user *) arg);

	case TIOCMIWAIT:
455 456
		return wait_modem_info(port, arg);

457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479
	default:
		break;
	}

	dbg("%s arg not supported", __func__);

	return -ENOIOCTLCMD;
}

static int ssu100_attach(struct usb_serial *serial)
{
	struct ssu100_port_private *priv;
	struct usb_serial_port *port = *serial->port;

	dbg("%s", __func__);

	priv = kzalloc(sizeof(*priv), GFP_KERNEL);
	if (!priv) {
		dev_err(&port->dev, "%s- kmalloc(%Zd) failed.\n", __func__,
			sizeof(*priv));
		return -ENOMEM;
	}

480
	spin_lock_init(&priv->status_lock);
481 482 483 484 485 486
	init_waitqueue_head(&priv->delta_msr_wait);
	usb_set_serial_port_data(port, priv);

	return ssu100_initdevice(serial->dev);
}

487
static int ssu100_tiocmget(struct tty_struct *tty)
488 489 490 491 492 493 494 495 496 497 498 499
{
	struct usb_serial_port *port = tty->driver_data;
	struct usb_device *dev = port->serial->dev;
	u8 *d;
	int r;

	dbg("%s\n", __func__);

	d = kzalloc(2, GFP_KERNEL);
	if (!d)
		return -ENOMEM;

500
	r = ssu100_getregister(dev, 0, UART_MCR, d);
501 502 503
	if (r < 0)
		goto mget_out;

504
	r = ssu100_getregister(dev, 0, UART_MSR, d+1);
505 506 507
	if (r < 0)
		goto mget_out;

508 509 510 511 512 513
	r = (d[0] & UART_MCR_DTR ? TIOCM_DTR : 0) |
		(d[0] & UART_MCR_RTS ? TIOCM_RTS : 0) |
		(d[1] & UART_MSR_CTS ? TIOCM_CTS : 0) |
		(d[1] & UART_MSR_DCD ? TIOCM_CAR : 0) |
		(d[1] & UART_MSR_RI ? TIOCM_RI : 0) |
		(d[1] & UART_MSR_DSR ? TIOCM_DSR : 0);
514 515 516 517 518 519

mget_out:
	kfree(d);
	return r;
}

520
static int ssu100_tiocmset(struct tty_struct *tty,
521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539
			   unsigned int set, unsigned int clear)
{
	struct usb_serial_port *port = tty->driver_data;
	struct usb_device *dev = port->serial->dev;

	dbg("%s\n", __func__);
	return update_mctrl(dev, set, clear);
}

static void ssu100_dtr_rts(struct usb_serial_port *port, int on)
{
	struct usb_device *dev = port->serial->dev;

	dbg("%s\n", __func__);

	mutex_lock(&port->serial->disc_mutex);
	if (!port->serial->disconnected) {
		/* Disable flow control */
		if (!on &&
540
		    ssu100_setregister(dev, 0, UART_MCR, 0) < 0)
541 542 543 544 545 546 547 548 549 550
			dev_err(&port->dev, "error from flowcontrol urb\n");
		/* drop RTS and DTR */
		if (on)
			set_mctrl(dev, TIOCM_DTR | TIOCM_RTS);
		else
			clear_mctrl(dev, TIOCM_DTR | TIOCM_RTS);
	}
	mutex_unlock(&port->serial->disc_mutex);
}

551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573
static void ssu100_update_msr(struct usb_serial_port *port, u8 msr)
{
	struct ssu100_port_private *priv = usb_get_serial_port_data(port);
	unsigned long flags;

	spin_lock_irqsave(&priv->status_lock, flags);
	priv->shadowMSR = msr;
	spin_unlock_irqrestore(&priv->status_lock, flags);

	if (msr & UART_MSR_ANY_DELTA) {
		/* update input line counters */
		if (msr & UART_MSR_DCTS)
			priv->icount.cts++;
		if (msr & UART_MSR_DDSR)
			priv->icount.dsr++;
		if (msr & UART_MSR_DDCD)
			priv->icount.dcd++;
		if (msr & UART_MSR_TERI)
			priv->icount.rng++;
		wake_up_interruptible(&priv->delta_msr_wait);
	}
}

574 575
static void ssu100_update_lsr(struct usb_serial_port *port, u8 lsr,
			      char *tty_flag)
576 577 578 579 580 581 582 583
{
	struct ssu100_port_private *priv = usb_get_serial_port_data(port);
	unsigned long flags;

	spin_lock_irqsave(&priv->status_lock, flags);
	priv->shadowLSR = lsr;
	spin_unlock_irqrestore(&priv->status_lock, flags);

584
	*tty_flag = TTY_NORMAL;
585
	if (lsr & UART_LSR_BRK_ERROR_BITS) {
586 587 588
		/* we always want to update icount, but we only want to
		 * update tty_flag for one case */
		if (lsr & UART_LSR_BI) {
589
			priv->icount.brk++;
590 591 592 593
			*tty_flag = TTY_BREAK;
			usb_serial_handle_break(port);
		}
		if (lsr & UART_LSR_PE) {
594
			priv->icount.parity++;
595 596 597 598 599 600 601 602 603
			if (*tty_flag == TTY_NORMAL)
				*tty_flag = TTY_PARITY;
		}
		if (lsr & UART_LSR_FE) {
			priv->icount.frame++;
			if (*tty_flag == TTY_NORMAL)
				*tty_flag = TTY_FRAME;
		}
		if (lsr & UART_LSR_OE){
604
			priv->icount.overrun++;
605 606 607
			if (*tty_flag == TTY_NORMAL)
				*tty_flag = TTY_OVERRUN;
		}
608
	}
609

610 611
}

612 613
static int ssu100_process_packet(struct urb *urb,
				 struct tty_struct *tty)
614
{
615 616
	struct usb_serial_port *port = urb->context;
	char *packet = (char *)urb->transfer_buffer;
617
	char flag = TTY_NORMAL;
618 619
	u32 len = urb->actual_length;
	int i;
620 621 622 623
	char *ch;

	dbg("%s - port %d", __func__, port->number);

624 625
	if ((len >= 4) &&
	    (packet[0] == 0x1b) && (packet[1] == 0x1b) &&
626
	    ((packet[2] == 0x00) || (packet[2] == 0x01))) {
627 628 629 630 631
		if (packet[2] == 0x00) {
			ssu100_update_lsr(port, packet[3], &flag);
			if (flag == TTY_OVERRUN)
				tty_insert_flip_char(tty, 0, TTY_OVERRUN);
		}
632 633
		if (packet[2] == 0x01)
			ssu100_update_msr(port, packet[3]);
634 635 636 637 638 639 640 641 642 643 644

		len -= 4;
		ch = packet + 4;
	} else
		ch = packet;

	if (!len)
		return 0;	/* status only */

	if (port->port.console && port->sysrq) {
		for (i = 0; i < len; i++, ch++) {
645
			if (!usb_serial_handle_sysrq_char(port, *ch))
646 647 648 649 650 651 652 653 654 655 656 657
				tty_insert_flip_char(tty, *ch, flag);
		}
	} else
		tty_insert_flip_string_fixed_flag(tty, ch, flag, len);

	return len;
}

static void ssu100_process_read_urb(struct urb *urb)
{
	struct usb_serial_port *port = urb->context;
	struct tty_struct *tty;
658
	int count;
659 660 661 662 663 664 665

	dbg("%s", __func__);

	tty = tty_port_tty_get(&port->port);
	if (!tty)
		return;

666
	count = ssu100_process_packet(urb, tty);
667 668 669 670 671 672 673 674 675 676 677 678 679 680 681 682 683 684 685 686 687 688 689

	if (count)
		tty_flip_buffer_push(tty);
	tty_kref_put(tty);
}

static struct usb_serial_driver ssu100_device = {
	.driver = {
		.owner = THIS_MODULE,
		.name = "ssu100",
	},
	.description	     = DRIVER_DESC,
	.id_table	     = id_table,
	.usb_driver	     = &ssu100_driver,
	.num_ports	     = 1,
	.open		     = ssu100_open,
	.close		     = ssu100_close,
	.attach              = ssu100_attach,
	.release             = ssu100_release,
	.dtr_rts             = ssu100_dtr_rts,
	.process_read_urb    = ssu100_process_read_urb,
	.tiocmget            = ssu100_tiocmget,
	.tiocmset            = ssu100_tiocmset,
690
	.get_icount	     = ssu100_get_icount,
691 692
	.ioctl               = ssu100_ioctl,
	.set_termios         = ssu100_set_termios,
693
	.disconnect          = usb_serial_generic_disconnect,
694 695 696 697 698 699 700 701 702 703 704 705 706 707 708 709 710 711 712 713 714 715 716 717 718 719 720 721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736
};

static int __init ssu100_init(void)
{
	int retval;

	dbg("%s", __func__);

	/* register with usb-serial */
	retval = usb_serial_register(&ssu100_device);

	if (retval)
		goto failed_usb_sio_register;

	retval = usb_register(&ssu100_driver);
	if (retval)
		goto failed_usb_register;

	printk(KERN_INFO KBUILD_MODNAME ": " DRIVER_VERSION ":"
	       DRIVER_DESC "\n");

	return 0;

failed_usb_register:
	usb_serial_deregister(&ssu100_device);
failed_usb_sio_register:
	return retval;
}

static void __exit ssu100_exit(void)
{
	usb_deregister(&ssu100_driver);
	usb_serial_deregister(&ssu100_device);
}

module_init(ssu100_init);
module_exit(ssu100_exit);

MODULE_DESCRIPTION(DRIVER_DESC);
MODULE_LICENSE("GPL");

module_param(debug, bool, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(debug, "Debug enabled or not");