[GITLAB] - UPGRADE TO v12 on Wednesday the 18th of December at 11.30AM

  1. 14 Nov, 2014 1 commit
    • Scott Carter's avatar
      pata_serverworks: disable 64-KB DMA transfers on Broadcom OSB4 IDE Controller · dd1e981a
      Scott Carter authored
      commit 37017ac6849e772e67dd187ba2fbd056c4afa533 upstream.
      
      The Broadcom OSB4 IDE Controller (vendor and device IDs: 1166:0211)
      does not support 64-KB DMA transfers.
      Whenever a 64-KB DMA transfer is attempted,
      the transfer fails and messages similar to the following
      are written to the console log:
      
         [ 2431.851125] sr 0:0:0:0: [sr0] Unhandled sense code
         [ 2431.851139] sr 0:0:0:0: [sr0]  Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
         [ 2431.851152] sr 0:0:0:0: [sr0]  Sense Key : Hardware Error [current]
         [ 2431.851166] sr 0:0:0:0: [sr0]  Add. Sense: Logical unit communication time-out
         [ 2431.851182] sr 0:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 76 f4 00 00 40 00
         [ 2431.851210] end_request: I/O error, dev sr0, sector 121808
      
      When the libata and pata_serverworks modules
      are recompiled with ATA_DEBUG and ATA_VERBOSE_DEBUG defined in libata.h,
      the 64-KB transfer size in the scatter-gather list can be seen
      in the console log:
      
         [ 2664.897267] sr 9:0:0:0: [sr0] Send:
         [ 2664.897274] 0xf63d85e0
         [ 2664.897283] sr 9:0:0:0: [sr0] CDB:
         [ 2664.897288] Read(10): 28 00 00 00 7f b4 00 00 40 00
         [ 2664.897319] buffer = 0xf6d6fbc0, bufflen = 131072, queuecommand 0xf81b7700
         [ 2664.897331] ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 00 00 7f b4 00 00 40
         [ 2664.897338] ata_scsi_translate: ENTER
         [ 2664.897345] ata_sg_setup: ENTER, ata1
         [ 2664.897356] ata_sg_setup: 3 sg elements mapped
         [ 2664.897364] ata_bmdma_fill_sg: PRD[0] = (0x66FD2000, 0xE000)
         [ 2664.897371] ata_bmdma_fill_sg: PRD[1] = (0x65000000, 0x10000)
         ------------------------------------------------------> =======
         [ 2664.897378] ata_bmdma_fill_sg: PRD[2] = (0x66A10000, 0x2000)
         [ 2664.897386] ata1: ata_dev_select: ENTER, device 0, wait 1
         [ 2664.897422] ata_sff_tf_load: feat 0x1 nsect 0x0 lba 0x0 0x0 0xFC
         [ 2664.897428] ata_sff_tf_load: device 0xA0
         [ 2664.897448] ata_sff_exec_command: ata1: cmd 0xA0
         [ 2664.897457] ata_scsi_translate: EXIT
         [ 2664.897462] leaving scsi_dispatch_cmnd()
         [ 2664.897497] Doing sr request, dev = sr0, block = 0
         [ 2664.897507] sr0 : reading 64/256 512 byte blocks.
         [ 2664.897553] ata_sff_hsm_move: ata1: protocol 7 task_state 1 (dev_stat 0x58)
         [ 2664.897560] atapi_send_cdb: send cdb
         [ 2666.910058] ata_bmdma_port_intr: ata1: host_stat 0x64
         [ 2666.910079] __ata_sff_port_intr: ata1: protocol 7 task_state 3
         [ 2666.910093] ata_sff_hsm_move: ata1: protocol 7 task_state 3 (dev_stat 0x51)
         [ 2666.910101] ata_sff_hsm_move: ata1: protocol 7 task_state 4 (dev_stat 0x51)
         [ 2666.910129] sr 9:0:0:0: [sr0] Done:
         [ 2666.910136] 0xf63d85e0 TIMEOUT
      
      lspci shows that the driver used for the Broadcom OSB4 IDE Controller is
      pata_serverworks:
      
         00:0f.1 IDE interface: Broadcom OSB4 IDE Controller (prog-if 8e [Master SecP SecO PriP])
                 Flags: bus master, medium devsel, latency 64
                 [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
                 [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
                 I/O ports at 0170 [size=8]
                 I/O ports at 0374 [size=4]
                 I/O ports at 1440 [size=16]
                 Kernel driver in use: pata_serverworks
      
      The pata_serverworks driver supports five distinct device IDs,
      one being the OSB4 and the other four belonging to the CSB series.
      The CSB series appears to support 64-KB DMA transfers,
      as tests on a machine with an SAI2 motherboard
      containing a Broadcom CSB5 IDE Controller (vendor and device IDs: 1166:0212)
      showed no problems with 64-KB DMA transfers.
      
      This problem was first discovered when attempting to install openSUSE
      from a DVD on a machine with an STL2 motherboard.
      Using the pata_serverworks module,
      older releases of openSUSE will not install at all due to the timeouts.
      Releases of openSUSE prior to 11.3 can be installed by disabling
      the pata_serverworks module using the brokenmodules boot parameter,
      which causes the serverworks module to be used instead.
      Recent releases of openSUSE (12.2 and later) include better error recovery and
      will install, though very slowly.
      On all openSUSE releases, the problem can be recreated
      on a machine containing a Broadcom OSB4 IDE Controller
      by mounting an install DVD and running a command similar to the following:
      
         find /mnt -type f -print | xargs cat > /dev/null
      
      The patch below corrects the problem.
      Similar to the other ATA drivers that do not support 64-KB DMA transfers,
      the patch changes the ata_port_operations qc_prep vector to point to a routine
      that breaks any 64-KB segment into two 32-KB segments and
      changes the scsi_host_template sg_tablesize element to reduce by half
      the number of scatter/gather elements allowed.
      These two changes affect only the OSB4.
      Signed-off-by: 's avatarScott Carter <ccscott@funsoft.com>
      Signed-off-by: 's avatarTejun Heo <tj@kernel.org>
      Signed-off-by: 's avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      dd1e981a
  2. 25 Jul, 2012 1 commit
    • Axel Lin's avatar
      ata: use module_pci_driver · 2fc75da0
      Axel Lin authored
      This patch converts the drivers in drivers/ata/* to use module_pci_driver()
      macro which makes the code smaller and a bit simpler.
      Signed-off-by: 's avatarAxel Lin <axel.lin@gmail.com>
      Cc: Alan Cox <alan@linux.intel.com>
      Cc: Jeff Garzik <jgarzik@pobox.com>
      Cc: Mikael Pettersson <mikpe@it.uu.se>
      Cc: Mark Lord <kernel@teksavvy.com>
      Cc: Jeremy Higdon <jeremy@sgi.com>
      Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
      Signed-off-by: 's avatarJeff Garzik <jgarzik@redhat.com>
      2fc75da0
  3. 14 Oct, 2011 3 commits
  4. 25 May, 2010 1 commit
  5. 19 May, 2010 1 commit
    • Tejun Heo's avatar
      libata-sff: clean up BMDMA initialization · c7087652
      Tejun Heo authored
      When BMDMA initialization failed or BMDMA was not available for
      whatever reason, bmdma_addr was left at zero and used as an indication
      that BMDMA shouldn't be used.  This leads to the following problems.
      
      p1. For BMDMA drivers which don't use traditional BMDMA register,
          ata_bmdma_mode_filter() incorrectly inhibits DMA modes.  Those
          drivers either have to inherit from ata_sff_port_ops or clear
          ->mode_filter explicitly.
      
      p2. non-BMDMA drivers call into BMDMA PRD table allocation.  It
          doesn't actually allocate PRD table if bmdma_addr is not
          initialized but is still confusing.
      
      p3. For BMDMA drivers which don't use traditional BMDMA register, some
          methods might not be invoked as expected (e.g. bmdma_stop from
          ata_sff_post_internal_cmd()).
      
      p4. SFF drivers w/ custom DMA interface implement noop BMDMA ops
          worrying libata core might call into one of them.
      
      These problems are caused by the muddy line between SFF and BMDMA and
      the assumption that all BMDMA controllers initialize bmdma_addr.
      
      This patch fixes p1 and p2 by removing the bmdma_addr assumption and
      moving prd allocation to BMDMA port start.  Later patches will fix the
      remaining issues.
      
      This patch improves BMDMA initialization such that
      
      * When BMDMA register initialization fails, falls back to PIO instead
        of failing.  ata_pci_bmdma_init() never fails now.
      
      * When ata_pci_bmdma_init() falls back to PIO, it clears
        ap->mwdma_mask and udma_mask instead of depending on
        ata_bmdma_mode_filter().  This makes ata_bmdma_mode_filter()
        unnecessary thus resolving p1.
      
      * ata_port_start() which actually is BMDMA specific is moved to
        ata_bmdma_port_start().  ata_port_start() and ata_sff_port_start()
        are killed.
      
      * ata_sff_port_start32() is moved and renamed to
        ata_bmdma_port_start32().
      
      Drivers which no longer call into PRD table allocation are...
      
        pdc_adma, sata_inic162x, sata_qstor, sata_sx4, pata_cmd640 and all
        drivers which inherit from ata_sff_port_ops.
      
      pata_icside sets ->port_start to ATA_OP_NULL as it doesn't need PRD
      but is a BMDMA controller and doesn't have custom port_start like
      other such controllers.
      
      Note that with the previous patch which makes all and only BMDMA
      drivers inherit from ata_bmdma_port_ops, this change doesn't break
      drivers which need PRD table.
      Signed-off-by: 's avatarTejun Heo <tj@kernel.org>
      Signed-off-by: 's avatarJeff Garzik <jgarzik@redhat.com>
      c7087652
  6. 01 Mar, 2010 3 commits
  7. 25 Mar, 2009 1 commit
  8. 29 Dec, 2008 1 commit
  9. 28 Oct, 2008 1 commit
  10. 17 Apr, 2008 6 commits
    • Tejun Heo's avatar
      libata: rename SFF functions · 9363c382
      Tejun Heo authored
      SFF functions have confusing names.  Some have sff prefix, some have
      bmdma, some std, some pci and some none.  Unify the naming by...
      
      * SFF functions which are common to both BMDMA and non-BMDMA are
        prefixed with ata_sff_.
      
      * SFF functions which are specific to BMDMA are prefixed with
        ata_bmdma_.
      
      * SFF functions which are specific to PCI but apply to both BMDMA and
        non-BMDMA are prefixed with ata_pci_sff_.
      
      * SFF functions which are specific to PCI and BMDMA are prefixed with
        ata_pci_bmdma_.
      
      * Drop generic prefixes from LLD specific routines.  For example,
        bfin_std_dev_select -> bfin_dev_select.
      
      The following renames are noteworthy.
      
        ata_qc_issue_prot() -> ata_sff_qc_issue()
        ata_pci_default_filter() -> ata_bmdma_mode_filter()
        ata_dev_try_classify() -> ata_sff_dev_classify()
      
      This rename is in preparation of separating SFF support out of libata
      core layer.  This patch strictly renames functions and doesn't
      introduce any behavior difference.
      Signed-off-by: 's avatarTejun Heo <htejun@gmail.com>
      9363c382
    • Tejun Heo's avatar
      libata: stop overloading port_info->private_data · 887125e3
      Tejun Heo authored
      port_info->private_data is currently used for two purposes - to record
      private data about the port_info or to specify host->private_data to
      use when allocating ata_host.
      
      This overloading is confusing and counter-intuitive in that
      port_info->private_data becomes host->private_data instead of
      port->private_data.  In addition, port_info and host don't correspond
      to each other 1-to-1.  Currently, the first non-NULL
      port_info->private_data is used.
      
      This patch makes port_info->private_data just be what it is -
      private_data for the port_info where LLD can jot down extra info.
      libata no longer sets host->private_data to the first non-NULL
      port_info->private_data, @host_priv argument is added to
      ata_pci_init_one() instead.  LLDs which use ata_pci_init_one() can use
      this argument to pass in pointer to host private data.  LLDs which
      don't should use init-register model anyway and can initialize
      host->private_data directly.
      
      Adding @host_priv instead of using init-register model for LLDs which
      use ata_pci_init_one() is suggested by Alan Cox.
      Signed-off-by: 's avatarTejun Heo <htejun@gmail.com>
      Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
      887125e3
    • Tejun Heo's avatar
      libata: make ata_pci_init_one() not use ops->irq_handler and pi->sht · 1bd5b715
      Tejun Heo authored
      ata_pci_init_one() is the only function which uses ops->irq_handler
      and pi->sht.  Other initialization functions take the same information
      as arguments.  This causes confusion and duplicate unused entries in
      structures.
      
      Make ata_pci_init_one() take sht as an argument and use ata_interrupt
      implicitly.  All current users use ata_interrupt and if different irq
      handler is necessary open coding ata_pci_init_one() using
      ata_prepare_sff_host() and ata_activate_sff_host can be done under ten
      lines including error handling and driver which requires custom
      interrupt handler is likely to require custom initialization anyway.
      
      As ata_pci_init_one() was the last user of ops->irq_handler, this
      patch also kills the field.
      Signed-off-by: 's avatarTejun Heo <htejun@gmail.com>
      1bd5b715
    • Tejun Heo's avatar
      libata: implement and use ops inheritance · 029cfd6b
      Tejun Heo authored
      libata lets low level drivers build ata_port_operations table and
      register it with libata core layer.  This allows low level drivers
      high level of flexibility but also burdens them with lots of
      boilerplate entries.
      
      This becomes worse for drivers which support related similar
      controllers which differ slightly.  They share most of the operations
      except for a few.  However, the driver still needs to list all
      operations for each variant.  This results in large number of
      duplicate entries, which is not only inefficient but also error-prone
      as it becomes very difficult to tell what the actual differences are.
      
      This duplicate boilerplates all over the low level drivers also make
      updating the core layer exteremely difficult and error-prone.  When
      compounded with multi-branched development model, it ends up
      accumulating inconsistencies over time.  Some of those inconsistencies
      cause immediate problems and fixed.  Others just remain there dormant
      making maintenance increasingly difficult.
      
      To rectify the problem, this patch implements ata_port_operations
      inheritance.  To allow LLDs to easily re-use their own ops tables
      overriding only specific methods, this patch implements poor man's
      class inheritance.  An ops table has ->inherits field which can be set
      to any ops table as long as it doesn't create a loop.  When the host
      is started, the inheritance chain is followed and any operation which
      isn't specified is taken from the nearest ancestor which has it
      specified.  This operation is called finalization and done only once
      per an ops table and the LLD doesn't have to do anything special about
      it other than making the ops table non-const such that libata can
      update it.
      
      libata provides four base ops tables lower drivers can inherit from -
      base, sata, pmp, sff and bmdma.  To avoid overriding these ops
      accidentaly, these ops are declared const and LLDs should always
      inherit these instead of using them directly.
      
      After finalization, all the ops table are identical before and after
      the patch except for setting .irq_handler to ata_interrupt in drivers
      which didn't use to.  The .irq_handler doesn't have any actual effect
      and the field will soon be removed by later patch.
      
      * sata_sx4 is still using old style EH and currently doesn't take
        advantage of ops inheritance.
      Signed-off-by: 's avatarTejun Heo <htejun@gmail.com>
      029cfd6b
    • Tejun Heo's avatar
      libata: implement and use SHT initializers · 68d1d07b
      Tejun Heo authored
      libata lets low level drivers build scsi_host_template and register it
      to the SCSI layer.  This allows low level drivers high level of
      flexibility but also burdens them with lots of boilerplate entries.
      
      This patch implements SHT initializers which can be used to initialize
      all the boilerplate entries in a sht.  Three variants of them are
      implemented - BASE, BMDMA and NCQ - for different types of drivers.
      Note that entries can be overriden by putting individual initializers
      after the helper macro.
      
      All sht tables are identical before and after this patch.
      Signed-off-by: 's avatarTejun Heo <htejun@gmail.com>
      68d1d07b
    • Tejun Heo's avatar
      libata: PCI device should be powered up before being accessed · f08048e9
      Tejun Heo authored
      PCI device should be powered up or powered up before its PCI regsiters
      are accessed.  Although PCI configuration register access is allowed
      in D3hot, PCI device is free to reset its status when transiting from
      D3hot to D0 causing configuration data to change.
      
      Many libata SFF drivers which use ata_pci_init_one() read and update
      configuration registers before calling ata_pci_init_one() which
      enables the PCI device.  Also, in resume paths, some drivers access
      registers without resuming the PCI device.
      
      This patch adds a call to pcim_enable_device() in init path if
      register is accessed before calling ata_pci_init_one() and make resume
      paths first resume PCI devices, access PCI configuration regiters then
      resume ATA host.
      
      While at it...
      
      * cmd640 was strange in that it set ->resume even when CONFIG_PM is
        not.  This is by-product of minimal build fix.  Updated.
      
      * In cs5530, Don't BUG() on reinit failure.  Just whine and fail
        resume.
      Signed-off-by: 's avatarTejun Heo <htejun@gmail.com>
      f08048e9
  11. 05 Mar, 2008 1 commit
  12. 23 Jan, 2008 1 commit
  13. 05 Nov, 2007 1 commit
  14. 12 Oct, 2007 3 commits
  15. 31 Aug, 2007 1 commit
  16. 11 Jul, 2007 1 commit
    • Auke Kok's avatar
      PCI: Change all drivers to use pci_device->revision · 44c10138
      Auke Kok authored
      Instead of all drivers reading pci config space to get the revision
      ID, they can now use the pci_device->revision member.
      
      This exposes some issues where drivers where reading a word or a dword
      for the revision number, and adding useless error-handling around the
      read. Some drivers even just read it for no purpose of all.
      
      In devices where the revision ID is being copied over and used in what
      appears to be the equivalent of hotpath, I have left the copy code
      and the cached copy as not to influence the driver's performance.
      
      Compile tested with make all{yes,mod}config on x86_64 and i386.
      Signed-off-by: 's avatarAuke Kok <auke-jan.h.kok@intel.com>
      Acked-by: 's avatarDave Jones <davej@redhat.com>
      Signed-off-by: 's avatarGreg Kroah-Hartman <gregkh@suse.de>
      44c10138
  17. 09 Jul, 2007 2 commits
  18. 22 May, 2007 1 commit
  19. 11 May, 2007 2 commits
    • Tejun Heo's avatar
      libata: clean up SFF init mess · 1626aeb8
      Tejun Heo authored
      The intention of using port_mask in SFF init helpers was to eventually
      support exoctic configurations such as combination of legacy and
      native port on the same controller.  This never became actually
      necessary and the related code always has been subtly broken one way
      or the other.  Now that new init model is in place, there is no reason
      to make common helpers capable of handling all corner cases.  Exotic
      cases can simply dealt within LLDs as necessary.
      
      This patch removes port_mask handling in SFF init helpers.  SFF init
      helpers don't take n_ports argument and interpret it into port_mask
      anymore.  All information is carried via port_info.  n_ports argument
      is dropped and always two ports are allocated.  LLD can tell SFF to
      skip certain port by marking it dummy.  Note that SFF code has been
      treating unuvailable ports this way for a long time until recent
      breakage fix from Linus and is consistent with how other drivers
      handle with unavailable ports.
      
      This fixes 1-port legacy host handling still broken after the recent
      native mode fix and simplifies SFF init logic.  The following changes
      are made...
      
      * ata_pci_init_native_host() and ata_init_legacy_host() both now try
        to initialized whatever they can and mark failed ports dummy.  They
        return 0 if any port is successfully initialized.
      
      * ata_pci_prepare_native_host() and ata_pci_init_one() now doesn't
        take n_ports argument.  All info should be specified via port_info
        array.  Always two ports are allocated.
      
      * ata_pci_init_bmdma() exported to be used by LLDs in exotic cases.
      
      * port_info handling in all LLDs are standardized - all port_info
        arrays are const stack variable named ppi.  Unless the second port
        is different from the first, its port_info is specified as NULL
        (tells libata that it's identical to the last non-NULL port_info).
      
      * pata_hpt37x/hpt3x2n: don't modify static variable directly.  Make an
        on-stack copy instead as ata_piix does.
      
      * pata_uli: It has 4 ports instead of 2.  Don't use
        ata_pci_prepare_native_host().  Allocate the host explicitly and use
        init helpers.  It's simple enough.
      Signed-off-by: 's avatarTejun Heo <htejun@gmail.com>
      Signed-off-by: 's avatarJeff Garzik <jeff@garzik.org>
      1626aeb8
    • Tejun Heo's avatar
      libata: reimplement suspend/resume support using sdev->manage_start_stop · 9666f400
      Tejun Heo authored
      Reimplement suspend/resume support using sdev->manage_start_stop.
      
      * Device suspend/resume is now SCSI layer's responsibility and the
        code is simplified a lot.
      
      * DPM is dropped.  This also simplifies code a lot.  Suspend/resume
        status is port-wide now.
      
      * ata_scsi_device_suspend/resume() and ata_dev_ready() removed.
      
      * Resume now has to wait for disk to spin up before proceeding.  I
        couldn't find easy way out as libata is in EH waiting for the
        disk to be ready and sd is waiting for EH to complete to issue
        START_STOP.
      
      * sdev->manage_start_stop is set to 1 in ata_scsi_slave_config().
        This fixes spindown on shutdown and suspend-to-disk.
      Signed-off-by: 's avatarTejun Heo <htejun@gmail.com>
      Signed-off-by: 's avatarJeff Garzik <jeff@garzik.org>
      9666f400
  20. 01 May, 2007 1 commit
    • Tejun Heo's avatar
      libata: add deadline support to prereset and reset methods · d4b2bab4
      Tejun Heo authored
      Add @deadline to prereset and reset methods and make them honor it.
      ata_wait_ready() which directly takes @deadline is implemented to be
      used as the wait function.  This patch is in preparation for EH timing
      improvements.
      
      * ata_wait_ready() never does busy sleep.  It's only used from EH and
        no wait in EH is that urgent.  This function also prints 'be
        patient' message automatically after 5 secs of waiting if more than
        3 secs is remaining till deadline.
      
      * ata_bus_post_reset() now fails with error code if any of its wait
        fails.  This is important because earlier reset tries will have
        shorter timeout than the spec requires.  If a device fails to
        respond before the short timeout, reset should be retried with
        longer timeout rather than silently ignoring the device.
      
        There are three behavior differences.
      
        1. Timeout is applied to both devices at once, not separately.  This
           is more consistent with what the spec says.
      
        2. When a device passes devchk but fails to become ready before
           deadline.  Previouly, post_reset would just succeed and let
           device classification remove the device.  New code fails the
           reset thus causing reset retry.  After a few times, EH will give
           up disabling the port.
      
        3. When slave device passes devchk but fails to become accessible
           (TF-wise) after reset.  Original code disables dev1 after 30s
           timeout and continues as if the device doesn't exist, while the
           patched code fails reset.  When this happens, new code fails
           reset on whole port rather than proceeding with only the primary
           device.
      
        If the failing device is suffering transient problems, new code
        retries reset which is a better behavior.  If the failing device is
        actually broken, the net effect is identical to it, but not to the
        other device sharing the channel.  In the previous code, reset would
        have succeeded after 30s thus detecting the working one.  In the new
        code, reset fails and whole port gets disabled.  IMO, it's a
        pathological case anyway (broken device sharing bus with working
        one) and doesn't really matter.
      
      * ata_bus_softreset() is changed to return error code from
        ata_bus_post_reset().  It used to return 0 unconditionally.
      
      * Spin up waiting is to be removed and not converted to honor
        deadline.
      
      * To be on the safe side, deadline is set to 40s for the time being.
      Signed-off-by: 's avatarTejun Heo <htejun@gmail.com>
      Signed-off-by: 's avatarJeff Garzik <jeff@garzik.org>
      d4b2bab4
  21. 28 Apr, 2007 2 commits
  22. 02 Mar, 2007 1 commit
  23. 26 Feb, 2007 1 commit
  24. 09 Feb, 2007 3 commits
    • Akira Iguchi's avatar
      libata: add another IRQ calls (libata drivers) · 246ce3b6
      Akira Iguchi authored
      This patch is against each libata driver.
      
      Two IRQ calls are added in ata_port_operations.
      - irq_on() is used to enable interrupts.
      - irq_ack() is used to acknowledge a device interrupt.
      
      In most drivers, ata_irq_on() and ata_irq_ack() are used for
      irq_on and irq_ack respectively.
      
      In some drivers (ex: ahci, sata_sil24) which cannot use them
      as is, ata_dummy_irq_on() and ata_dummy_irq_ack() are used.
      Signed-off-by: 's avatarKou Ishizaki <kou.ishizaki@toshiba.co.jp>
      Signed-off-by: 's avatarAkira Iguchi <akira2.iguchi@toshiba.co.jp>
      Signed-off-by: 's avatarJeff Garzik <jeff@garzik.org>
      246ce3b6
    • Tejun Heo's avatar
      libata: convert to iomap · 0d5ff566
      Tejun Heo authored
      Convert libata core layer and LLDs to use iomap.
      
      * managed iomap is used.  Pointer to pcim_iomap_table() is cached at
        host->iomap and used through out LLDs.  This basically replaces
        host->mmio_base.
      
      * if possible, pcim_iomap_regions() is used
      
      Most iomap operation conversions are taken from Jeff Garzik
      <jgarzik@pobox.com>'s iomap branch.
      Signed-off-by: 's avatarTejun Heo <htejun@gmail.com>
      Signed-off-by: 's avatarJeff Garzik <jeff@garzik.org>
      0d5ff566
    • Tejun Heo's avatar
      libata: update libata LLDs to use devres · 24dc5f33
      Tejun Heo authored
      Update libata LLDs to use devres.  Core layer is already converted to
      support managed LLDs.  This patch simplifies initialization and fixes
      many resource related bugs in init failure and detach path.  For
      example, all converted drivers now handle ata_device_add() failure
      gracefully without excessive resource rollback code.
      
      As most resources are released automatically on driver detach, many
      drivers don't need or can do with much simpler ->{port|host}_stop().
      In general, stop callbacks are need iff port or host needs to be given
      commands to shut it down.  Note that freezing is enough in many cases
      and ports are automatically frozen before being detached.
      Signed-off-by: 's avatarTejun Heo <htejun@gmail.com>
      Signed-off-by: 's avatarJeff Garzik <jeff@garzik.org>
      24dc5f33