usrp_lib.cpp 27.2 KB
Newer Older
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
/*
 * Licensed to the OpenAirInterface (OAI) Software Alliance under one or more
 * contributor license agreements.  See the NOTICE file distributed with
 * this work for additional information regarding copyright ownership.
 * The OpenAirInterface Software Alliance licenses this file to You under
 * the OAI Public License, Version 1.0  (the "License"); you may not use this file
 * except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *      http://www.openairinterface.org/?page_id=698
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 *-------------------------------------------------------------------------------
 * For more information about the OpenAirInterface (OAI) Software Alliance:
 *      contact@openairinterface.org
 */

22 23
/** usrp_lib.cpp
 *
24
 * \author: HongliangXU : hong-liang-xu@agilent.com
25 26 27 28 29 30 31 32
 */

#include <string.h>
#include <pthread.h>
#include <unistd.h>
#include <stdio.h>
#include <uhd/utils/thread_priority.hpp>
#include <uhd/usrp/multi_usrp.hpp>
33
#include <uhd/version.hpp>
34 35 36 37 38 39
#include <boost/lexical_cast.hpp>
#include <boost/algorithm/string.hpp>
#include <iostream>
#include <complex>
#include <fstream>
#include <cmath>
40
#include <time.h>
41
#include "UTIL/LOG/log_extern.h"
42
#include "common_lib.h"
43 44 45 46 47 48 49
#ifdef __SSE4_1__
#  include <smmintrin.h>
#endif
 
#ifdef __AVX2__
#  include <immintrin.h>
#endif
50

51 52 53 54
#ifdef __arm__
#  include <arm_neon.h>
#endif

55 56 57 58 59
/** @addtogroup _USRP_PHY_RF_INTERFACE_
 * @{
 */

/*! \brief USRP Configuration */ 
60 61 62 63 64 65
typedef struct
{

  // --------------------------------
  // variables for USRP configuration
  // --------------------------------
66
  //! USRP device pointer
67 68
  uhd::usrp::multi_usrp::sptr usrp;
  //uhd::usrp::multi_usrp::sptr rx_usrp;
69
  
70
  //create a send streamer and a receive streamer
71
  //! USRP TX Stream
72
  uhd::tx_streamer::sptr tx_stream;
73
  //! USRP RX Stream
74 75
  uhd::rx_streamer::sptr rx_stream;

76
  //! USRP TX Metadata
77
  uhd::tx_metadata_t tx_md;
78
  //! USRP RX Metadata
79 80
  uhd::rx_metadata_t rx_md;

81
  //! USRP Timestamp Information
82
  uhd::time_spec_t tm_spec;
83

84
  //setup variables and allocate buffer
85
  //! USRP Metadata
86 87
  uhd::async_metadata_t async_md;

88
  //! Sampling rate
89
  double sample_rate;
90 91

  //! time offset between transmiter timestamp and receiver timestamp;
92
  double tdiff;
93 94

  //! TX forward samples. We use usrp_time_offset to get this value
95 96 97 98 99 100
  int tx_forward_nsamps; //166 for 20Mhz


  // --------------------------------
  // Debug and output control
  // --------------------------------
101
  //! Number of underflows
102
  int num_underflows;
103
  //! Number of overflows
104
  int num_overflows;
105 106
  
  //! Number of sequential errors
107
  int num_seq_errors;
108
  //! tx count
109
  int64_t tx_count;
110
  //! rx count
111
  int64_t rx_count;
112
  //! timestamp of RX packet
113 114 115 116
  openair0_timestamp rx_timestamp;

} usrp_state_t;

117 118 119
/*! \brief Called to start the USRP transceiver. Return 0 if OK, < 0 if error
    @param device pointer to the device structure specific to the RF hardware target
*/
120 121 122 123 124 125
static int trx_usrp_start(openair0_device *device)
{
  usrp_state_t *s = (usrp_state_t*)device->priv;

  // init recv and send streaming
  uhd::stream_cmd_t cmd(uhd::stream_cmd_t::STREAM_MODE_START_CONTINUOUS);
126
  cmd.time_spec = s->usrp->get_time_now() + uhd::time_spec_t(0.05);
127 128 129
  cmd.stream_now = false; // start at constant delay
  s->rx_stream->issue_stream_cmd(cmd);

130
  s->tx_md.time_spec = cmd.time_spec + uhd::time_spec_t(1-(double)s->tx_forward_nsamps/s->sample_rate);
131 132 133 134 135 136 137 138
  s->tx_md.has_time_spec = true;
  s->tx_md.start_of_burst = true;
  s->tx_md.end_of_burst = false;


  s->rx_count = 0;
  s->tx_count = 0;
  s->rx_timestamp = 0;
139 140

  return 0;
141
}
142 143 144
/*! \brief Terminate operation of the USRP transceiver -- free all associated resources 
 * \param device the hardware to use
 */
145 146 147 148 149 150
static void trx_usrp_end(openair0_device *device)
{
  usrp_state_t *s = (usrp_state_t*)device->priv;

  s->rx_stream->issue_stream_cmd(uhd::stream_cmd_t::STREAM_MODE_STOP_CONTINUOUS);

navid's avatar
navid committed
151 152 153 154 155
  //send a mini EOB packet
  s->tx_md.end_of_burst = true;
  s->tx_stream->send("", 0, s->tx_md);
  s->tx_md.end_of_burst = false;
  
156
}
157

158 159 160 161 162 163 164 165
/*! \brief Called to send samples to the USRP RF target
      @param device pointer to the device structure specific to the RF hardware target
      @param timestamp The timestamp at whicch the first sample MUST be sent 
      @param buff Buffer which holds the samples
      @param nsamps number of samples to be sent
      @param antenna_id index of the antenna if the device has multiple anteannas
      @param flags flags must be set to TRUE if timestamp parameter needs to be applied
*/ 
166
static int trx_usrp_write(openair0_device *device, openair0_timestamp timestamp, void **buff, int nsamps, int cc, int flags)
167
{
168 169 170 171 172 173 174
   static long long int loop=0;
   static long time_min=0, time_max=0, time_avg=0;
   struct timespec tp_start, tp_end;
   long time_diff;
   clock_gettime(CLOCK_MONOTONIC_RAW, &tp_start);

  int ret=0, ret_i=0;
175
  usrp_state_t *s = (usrp_state_t*)device->priv;
knopp's avatar
knopp committed
176

177
  s->tx_md.time_spec = uhd::time_spec_t::from_ticks(timestamp, s->sample_rate);
knopp's avatar
knopp committed
178

179
  
180 181 182 183
  if(flags)
    s->tx_md.has_time_spec = true;
  else
    s->tx_md.has_time_spec = false;
184
  
knopp's avatar
knopp committed
185 186 187
  if (cc>1) {
    std::vector<void *> buff_ptrs;
    for (int i=0;i<cc;i++) buff_ptrs.push_back(buff[i]);
188
    ret = (int)s->tx_stream->send(buff_ptrs, nsamps, s->tx_md,1e-3);
knopp's avatar
knopp committed
189 190
  }
  else
191 192
    ret = (int)s->tx_stream->send(buff[0], nsamps, s->tx_md,1e-3);

193
  s->tx_md.start_of_burst = false;
194

195 196 197
  if (ret != nsamps) {
    printf("[xmit] tx samples %d != %d\n",ret,nsamps);
  }
198 199 200 201 202 203 204 205 206 207 208

  clock_gettime(CLOCK_MONOTONIC_RAW, &tp_end);
  time_diff = (tp_end.tv_sec - tp_start.tv_sec) *1E09  + (tp_end.tv_nsec - tp_start.tv_nsec);
  if  (time_min==0 ||loop==1 || time_min > time_diff)
    time_min=time_diff;
  if  (time_max==0 ||loop==1 || time_max < time_diff)
    time_max=time_diff;
  if (time_avg ==0 ||loop==1)
    time_avg= time_diff;
  else
    time_avg=(time_diff+time_avg) /2.0;
209

210
  /*   //prints statics of uhd every 10 seconds
211 212
   if ( loop % (10 * ((int)device->openair0_cfg[0].sample_rate /(int)nsamps )) ==0)
     LOG_I(HW,"usrp_write: min(ns)=%d, max(ns)=%d, avg(ns)=%d\n", (int)time_min, (int)time_max,(int)time_avg);
213
  */
214
   loop++;
215
  return ret;
216 217
}

218 219 220 221 222 223 224 225 226 227 228
/*! \brief Receive samples from hardware.
 * Read \ref nsamps samples from each channel to buffers. buff[0] is the array for
 * the first channel. *ptimestamp is the time at which the first sample
 * was received.
 * \param device the hardware to use
 * \param[out] ptimestamp the time at which the first sample was received.
 * \param[out] buff An array of pointers to buffers for received samples. The buffers must be large enough to hold the number of samples \ref nsamps.
 * \param nsamps Number of samples. One sample is 2 byte I + 2 byte Q => 4 byte.
 * \param antenna_id Index of antenna for which to receive samples
 * \returns the number of sample read
*/
229
static int trx_usrp_read(openair0_device *device, openair0_timestamp *ptimestamp, void **buff, int nsamps, int cc)
230
{
231 232 233 234 235
   static long long int loop=0;
   static long time_min=0, time_max=0, time_avg=0;
   struct timespec tp_start, tp_end;
   long time_diff;
   clock_gettime(CLOCK_MONOTONIC_RAW, &tp_start);
236 237 238 239 240 241
   usrp_state_t *s = (usrp_state_t*)device->priv;
   int samples_received=0,i,j;
   int nsamps2;  // aligned to upper 32 or 16 byte boundary
#if defined(__x86_64) || defined(__i386__)
#ifdef __AVX2__
   nsamps2 = (nsamps+7)>>3;
242
   __m256i buff_tmp[2][nsamps2];
243 244
#else
   nsamps2 = (nsamps+3)>>2;
245
   __m128i buff_tmp[2][nsamps2];
246 247 248
#endif
#elif defined(__arm__)
   nsamps2 = (nsamps+3)>>2;
249
   int16x8_t buff_tmp[2][nsamps2];
250 251
#endif

252

253
  if (device->type == USRP_B200_DEV) {  
254
    if (cc>1) {
gauthier's avatar
gauthier committed
255
    // receive multiple channels (e.g. RF A and RF B)
256
      std::vector<void *> buff_ptrs;
257
 
258 259 260
      for (int i=0;i<cc;i++) buff_ptrs.push_back(buff_tmp[i]);
      samples_received = s->rx_stream->recv(buff_ptrs, nsamps, s->rx_md);
    } else {
gauthier's avatar
gauthier committed
261
    // receive a single channel (e.g. from connector RF A)
262 263
      samples_received = s->rx_stream->recv(buff_tmp[0], nsamps, s->rx_md);
    }
264

265
  // bring RX data into 12 LSBs for softmodem RX
266 267
    for (int i=0;i<cc;i++) {
      for (int j=0; j<nsamps2; j++) {      
268 269
#if defined(__x86_64__) || defined(__i386__)
#ifdef __AVX2__
270
        ((__m256i *)buff[i])[j] = _mm256_srai_epi16(buff_tmp[i][j],4);
271
#else
272
        ((__m128i *)buff[i])[j] = _mm_srai_epi16(buff_tmp[i][j],4);
273 274
#endif
#elif defined(__arm__)
275
        ((int16x8_t*)buff[i])[j] = vshrq_n_s16(buff_tmp[i][j],4);
276
#endif
277
      }
278
    }
279
  } else if (device->type == USRP_X300_DEV) {
280
    if (cc>1) { 
281 282 283 284 285 286 287 288
    // receive multiple channels (e.g. RF A and RF B)
      std::vector<void *> buff_ptrs;
 
      for (int i=0;i<cc;i++) buff_ptrs.push_back(buff[i]);
      samples_received = s->rx_stream->recv(buff_ptrs, nsamps, s->rx_md);
    } else {
    // receive a single channel (e.g. from connector RF A)
      samples_received = s->rx_stream->recv(buff[0], nsamps, s->rx_md);
289
    }
290
  }
291

292 293 294 295
  if (samples_received < nsamps) {
    printf("[recv] received %d samples out of %d\n",samples_received,nsamps);
    
  }
296

297 298 299 300 301 302 303 304 305 306 307 308 309 310 311
  //handle the error code
  switch(s->rx_md.error_code){
  case uhd::rx_metadata_t::ERROR_CODE_NONE:
    break;
  case uhd::rx_metadata_t::ERROR_CODE_OVERFLOW:
    printf("[recv] USRP RX OVERFLOW!\n");
    s->num_overflows++;
    break;
  case uhd::rx_metadata_t::ERROR_CODE_TIMEOUT:
    printf("[recv] USRP RX TIMEOUT!\n");
    break;
  default:
    printf("[recv] Unexpected error on RX, Error code: 0x%x\n",s->rx_md.error_code);
    break;
  }
312 313 314
  s->rx_count += nsamps;
  s->rx_timestamp = s->rx_md.time_spec.to_ticks(s->sample_rate);
  *ptimestamp = s->rx_timestamp;
315

316 317 318 319 320 321 322 323 324 325
  clock_gettime(CLOCK_MONOTONIC_RAW, &tp_end);
  time_diff = (tp_end.tv_sec - tp_start.tv_sec) *1E09  + (tp_end.tv_nsec - tp_start.tv_nsec);
  if  (time_min==0 ||loop==1 || time_min > time_diff)
    time_min=time_diff;
  if  (time_max==0 ||loop==1 || time_max < time_diff)
    time_max=time_diff;
  if (time_avg ==0 ||loop==1)
    time_avg= time_diff;
  else
    time_avg=(time_diff+time_avg) /2.0;
326
  /*
327 328 329 330
  //prints statics of uhd every 10 seconds
  if ( loop % (10 * ((int)device->openair0_cfg[0].sample_rate /(int)nsamps )) ==0)
     LOG_I(HW,"usrp_read: min(ns)=%d, max(ns)=%d, avg(ns)=%d\n", (int)time_min, (int)time_max,(int)time_avg);

331
     loop++;*/
332 333 334
  return samples_received;
}

335 336 337
/*! \brief Get current timestamp of USRP
 * \param device the hardware to use
*/
338 339 340 341 342 343 344 345
openair0_timestamp get_usrp_time(openair0_device *device) 
{
 
  usrp_state_t *s = (usrp_state_t*)device->priv;
  
  return s->usrp->get_time_now().to_ticks(s->sample_rate);
} 

346 347 348 349
/*! \brief Compares two variables within precision
 * \param a first variable
 * \param b second variable
*/
350 351 352 353
static bool is_equal(double a, double b)
{
  return std::fabs(a-b) < std::numeric_limits<double>::epsilon();
}
354

355 356 357 358 359 360
/*! \brief Set frequencies (TX/RX)
 * \param device the hardware to use
 * \param openair0_cfg RF frontend parameters set by application
 * \param dummy dummy variable not used
 * \returns 0 in success 
 */
361
int trx_usrp_set_freq(openair0_device* device, openair0_config_t *openair0_cfg, int dummy) {
362 363 364

  usrp_state_t *s = (usrp_state_t*)device->priv;

365
  printf("Setting USRP TX Freq %f, RX Freq %f\n",openair0_cfg[0].tx_freq[0],openair0_cfg[0].rx_freq[0]);
366 367 368 369 370 371 372
  s->usrp->set_tx_freq(openair0_cfg[0].tx_freq[0]);
  s->usrp->set_rx_freq(openair0_cfg[0].rx_freq[0]);

  return(0);
  
}

373 374 375 376 377
/*! \brief Set RX frequencies 
 * \param device the hardware to use
 * \param openair0_cfg RF frontend parameters set by application
 * \returns 0 in success 
 */
378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394
int openair0_set_rx_frequencies(openair0_device* device, openair0_config_t *openair0_cfg) {

  usrp_state_t *s = (usrp_state_t*)device->priv;
  static int first_call=1;
  static double rf_freq,diff;

  uhd::tune_request_t rx_tune_req(openair0_cfg[0].rx_freq[0]);

  rx_tune_req.rf_freq_policy = uhd::tune_request_t::POLICY_MANUAL;
  rx_tune_req.rf_freq = openair0_cfg[0].rx_freq[0];
  rf_freq=openair0_cfg[0].rx_freq[0];
  s->usrp->set_rx_freq(rx_tune_req);

  return(0);
  
}

395 396 397 398 399
/*! \brief Set Gains (TX/RX)
 * \param device the hardware to use
 * \param openair0_cfg RF frontend parameters set by application
 * \returns 0 in success 
 */
400
int trx_usrp_set_gains(openair0_device* device, 
401
		       openair0_config_t *openair0_cfg) {
402 403 404 405

  usrp_state_t *s = (usrp_state_t*)device->priv;

  s->usrp->set_tx_gain(openair0_cfg[0].tx_gain[0]);
406 407 408 409 410 411 412 413 414
  ::uhd::gain_range_t gain_range = s->usrp->get_rx_gain_range(0);
  // limit to maximum gain
  if (openair0_cfg[0].rx_gain[0]-openair0_cfg[0].rx_gain_offset[0] > gain_range.stop()) {
    
    printf("RX Gain 0 too high, reduce by %f dB\n",
	   openair0_cfg[0].rx_gain[0]-openair0_cfg[0].rx_gain_offset[0] - gain_range.stop());	   
    exit(-1);
  }
  s->usrp->set_rx_gain(openair0_cfg[0].rx_gain[0]-openair0_cfg[0].rx_gain_offset[0]);
415
  printf("Setting USRP RX gain to %f (rx_gain %f,gain_range.stop() %f)\n", openair0_cfg[0].rx_gain[0]-openair0_cfg[0].rx_gain_offset[0],openair0_cfg[0].rx_gain[0],gain_range.stop());
416

417 418
  return(0);
}
419

420 421 422
/*! \brief Stop USRP
 * \param card refers to the hardware index to use
 */
423
int trx_usrp_stop(openair0_device* device) {
424 425
  return(0);
}
426

427
/*! \brief USRPB210 RX calibration table */
428
rx_gain_calib_table_t calib_table_b210[] = {
Raymond Knopp's avatar
Raymond Knopp committed
429 430 431 432 433
  {3500000000.0,44.0},
  {2660000000.0,49.0},
  {2300000000.0,50.0},
  {1880000000.0,53.0},
  {816000000.0,58.0},
434 435
  {-1,0}};

436
/*! \brief USRPB210 RX calibration table */
437 438 439 440 441 442
rx_gain_calib_table_t calib_table_b210_38[] = {
  {3500000000.0,44.0},
  {2660000000.0,49.8},
  {2300000000.0,51.0},
  {1880000000.0,53.0},
  {816000000.0,57.0},
443 444
  {-1,0}};

445
/*! \brief USRPx310 RX calibration table */
446 447
rx_gain_calib_table_t calib_table_x310[] = {
  {3500000000.0,77.0},
448
  {2660000000.0,81.0},
449 450
  {2300000000.0,81.0},
  {1880000000.0,82.0},
451
  {816000000.0,85.0},
452 453
  {-1,0}};

454 455 456 457 458
/*! \brief Set RX gain offset 
 * \param openair0_cfg RF frontend parameters set by application
 * \param chain_index RF chain to apply settings to
 * \returns 0 in success 
 */
459
void set_rx_gain_offset(openair0_config_t *openair0_cfg, int chain_index,int bw_gain_adjust) {
460 461 462

  int i=0;
  // loop through calibration table to find best adjustment factor for RX frequency
463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488
  double min_diff = 6e9,diff,gain_adj=0.0;
  if (bw_gain_adjust==1) {
    switch ((int)openair0_cfg[0].sample_rate) {
    case 30720000:      
      break;
    case 23040000:
      gain_adj=1.25;
      break;
    case 15360000:
      gain_adj=3.0;
      break;
    case 7680000:
      gain_adj=6.0;
      break;
    case 3840000:
      gain_adj=9.0;
      break;
    case 1920000:
      gain_adj=12.0;
      break;
    default:
      printf("unknown sampling rate %d\n",(int)openair0_cfg[0].sample_rate);
      exit(-1);
      break;
    }
  }
489 490
  while (openair0_cfg->rx_gain_calib_table[i].freq>0) {
    diff = fabs(openair0_cfg->rx_freq[chain_index] - openair0_cfg->rx_gain_calib_table[i].freq);
491
    printf("cal %d: freq %f, offset %f, diff %f\n",
492 493 494
	   i,
	   openair0_cfg->rx_gain_calib_table[i].freq,
	   openair0_cfg->rx_gain_calib_table[i].offset,diff);
495 496
    if (min_diff > diff) {
      min_diff = diff;
497
      openair0_cfg->rx_gain_offset[chain_index] = openair0_cfg->rx_gain_calib_table[i].offset+gain_adj;
498 499 500 501 502 503
    }
    i++;
  }
  
}

504 505 506 507
/*! \brief print the USRP statistics  
* \param device the hardware to use
* \returns  0 on success
*/
508
int trx_usrp_get_stats(openair0_device* device) {
509

510 511 512
  return(0);

}
513 514 515 516 517

/*! \brief Reset the USRP statistics  
* \param device the hardware to use
* \returns  0 on success
*/
518
int trx_usrp_reset_stats(openair0_device* device) {
519 520 521 522

  return(0);

}
523

524

525

526
extern "C" {
527 528 529 530
/*! \brief Initialize Openair USRP target. It returns 0 if OK
* \param device the hardware to use
* \param openair0_cfg RF frontend parameters set by application
*/
531
  int device_init(openair0_device* device, openair0_config_t *openair0_cfg) {
532
    
533 534 535 536 537
    uhd::set_thread_priority_safe(1.0);
    usrp_state_t *s = (usrp_state_t*)malloc(sizeof(usrp_state_t));
    memset(s, 0, sizeof(usrp_state_t));
    
    // Initialize USRP device
538

539
  device->openair0_cfg = openair0_cfg;
540

541
  std::string args = "type=b200";
knopp's avatar
knopp committed
542 543


544
  uhd::device_addrs_t device_adds = uhd::device::find(args);
545
  size_t i;
546 547 548 549 550
  
  int vers=0,subvers=0,subsubvers=0;
  int bw_gain_adjust=0;

  sscanf(uhd::get_version_string().c_str(),"%d.%d.%d",&vers,&subvers,&subsubvers);
551

552
  printf("Checking for USRPs : UHD %s (%d.%d.%d)\n",uhd::get_version_string().c_str(),vers,subvers,subsubvers);
553
  
554 555
  if(device_adds.size() == 0)
  {
556 557 558 559 560 561 562
    double usrp_master_clock = 184.32e6;

    std::string args = "type=x300";
    
    // workaround for an api problem, master clock has to be set with the constructor not via set_master_clock_rate
    args += boost::str(boost::format(",master_clock_rate=%f") % usrp_master_clock);
    
knopp's avatar
knopp committed
563
//    args += ",num_send_frames=256,num_recv_frames=256, send_frame_size=4096, recv_frame_size=4096";
564
    
565
    uhd::device_addrs_t device_adds = uhd::device::find(args);
566

567 568 569 570 571
    if(device_adds.size() == 0)
    {
      std::cerr<<"No USRP Device Found. " << std::endl;
      free(s);
      return -1;
knopp's avatar
knopp committed
572

573
    }
knopp's avatar
knopp committed
574

575

576 577 578 579 580 581 582 583
    printf("Found USRP X300\n");
    s->usrp = uhd::usrp::multi_usrp::make(args);
    //  s->usrp->set_rx_subdev_spec(rx_subdev);
    //  s->usrp->set_tx_subdev_spec(tx_subdev);

    // lock mboard clocks
    s->usrp->set_clock_source("internal");
    
584
    //Setting device type to USRP X300/X310 
585
    device->type=USRP_X300_DEV;
586

587 588 589
    // this is not working yet, master clock has to be set via constructor
    // set master clock rate and sample rate for tx & rx for streaming
    //s->usrp->set_master_clock_rate(usrp_master_clock);
590 591

    openair0_cfg[0].rx_gain_calib_table = calib_table_x310;
592
    
593 594
    switch ((int)openair0_cfg[0].sample_rate) {
    case 30720000:
595
            // from usrp_time_offset
596
      //openair0_cfg[0].samples_per_packet    = 2048;
597
      openair0_cfg[0].tx_sample_advance     = 15;
598 599
      openair0_cfg[0].tx_bw                 = 20e6;
      openair0_cfg[0].rx_bw                 = 20e6;
600
      break;
601
    case 15360000:
602
      //openair0_cfg[0].samples_per_packet    = 2048;
603
      openair0_cfg[0].tx_sample_advance     = 45;
604 605
      openair0_cfg[0].tx_bw                 = 10e6;
      openair0_cfg[0].rx_bw                 = 10e6;
606
      break;
607
    case 7680000:
608
      //openair0_cfg[0].samples_per_packet    = 2048;
609
      openair0_cfg[0].tx_sample_advance     = 50;
610 611
      openair0_cfg[0].tx_bw                 = 5e6;
      openair0_cfg[0].rx_bw                 = 5e6;
612
      break;
613
    case 1920000:
614
      //openair0_cfg[0].samples_per_packet    = 2048;
615
      openair0_cfg[0].tx_sample_advance     = 50;
616 617
      openair0_cfg[0].tx_bw                 = 1.25e6;
      openair0_cfg[0].rx_bw                 = 1.25e6;
618 619 620 621 622 623 624
      break;
    default:
      printf("Error: unknown sampling rate %f\n",openair0_cfg[0].sample_rate);
      exit(-1);
      break;
    }

625 626
  } else {
    printf("Found USRP B200");
627
    args += ",num_send_frames=256,num_recv_frames=256, send_frame_size=15360, recv_frame_size=15360" ; 
628 629 630 631
    s->usrp = uhd::usrp::multi_usrp::make(args);

    //  s->usrp->set_rx_subdev_spec(rx_subdev);
    //  s->usrp->set_tx_subdev_spec(tx_subdev);
632 633 634 635
    
    // do not explicitly set the clock to "internal", because this will disable the gpsdo
    //    // lock mboard clocks
    //    s->usrp->set_clock_source("internal");
636
    // set master clock rate and sample rate for tx & rx for streaming
637

638
    device->type = USRP_B200_DEV;
639

knopp's avatar
knopp committed
640

641 642 643 644 645 646 647 648
    if ((vers == 3) && (subvers == 9) && (subsubvers>=2)) {
      openair0_cfg[0].rx_gain_calib_table = calib_table_b210;
      bw_gain_adjust=0;
    }
    else {
      openair0_cfg[0].rx_gain_calib_table = calib_table_b210_38;
      bw_gain_adjust=1;
    }
649

650 651
    switch ((int)openair0_cfg[0].sample_rate) {
    case 30720000:
652
      s->usrp->set_master_clock_rate(30.72e6);
653
      //openair0_cfg[0].samples_per_packet    = 1024;
654
      openair0_cfg[0].tx_sample_advance     = 115;
655 656
      openair0_cfg[0].tx_bw                 = 20e6;
      openair0_cfg[0].rx_bw                 = 20e6;
657
      break;
658
    case 23040000:
659
      s->usrp->set_master_clock_rate(23.04e6); //to be checked
660
      //openair0_cfg[0].samples_per_packet    = 1024;
661
      openair0_cfg[0].tx_sample_advance     = 113;
662 663
      openair0_cfg[0].tx_bw                 = 20e6;
      openair0_cfg[0].rx_bw                 = 20e6;
664
      break;
665
    case 15360000:
666
      s->usrp->set_master_clock_rate(30.72e06);
667
      //openair0_cfg[0].samples_per_packet    = 1024;
668
      openair0_cfg[0].tx_sample_advance     = 103; 
669 670
      openair0_cfg[0].tx_bw                 = 20e6;
      openair0_cfg[0].rx_bw                 = 20e6;
671
      break;
672
    case 7680000:
Rohit Gupta's avatar
Rohit Gupta committed
673
      s->usrp->set_master_clock_rate(30.72e6);
674
      //openair0_cfg[0].samples_per_packet    = 1024;
675
      openair0_cfg[0].tx_sample_advance     = 80;
676 677
      openair0_cfg[0].tx_bw                 = 20e6;
      openair0_cfg[0].rx_bw                 = 20e6;
678
      break;
679
    case 1920000:
680
      s->usrp->set_master_clock_rate(30.72e6);
681
      //openair0_cfg[0].samples_per_packet    = 1024;
682
      openair0_cfg[0].tx_sample_advance     = 40;
683 684
      openair0_cfg[0].tx_bw                 = 20e6;
      openair0_cfg[0].rx_bw                 = 20e6;
685 686 687 688 689 690 691
      break;
    default:
      printf("Error: unknown sampling rate %f\n",openair0_cfg[0].sample_rate);
      exit(-1);
      break;
    }
  }
knopp's avatar
knopp committed
692

693
  /* device specific */
694 695
  //openair0_cfg[0].txlaunch_wait = 1;//manage when TX processing is triggered
  //openair0_cfg[0].txlaunch_wait_slotcount = 1; //manage when TX processing is triggered
696 697
  openair0_cfg[0].iq_txshift = 4;//shift
  openair0_cfg[0].iq_rxrescale = 15;//rescale iqs
698
  
699
  for(i=0;i<s->usrp->get_rx_num_channels();i++) {
700
    if (i<openair0_cfg[0].rx_num_channels) {
knopp's avatar
knopp committed
701
      s->usrp->set_rx_rate(openair0_cfg[0].sample_rate,i);
702 703
      //s->usrp->set_rx_bandwidth(openair0_cfg[0].rx_bw,i);
      //printf("Setting rx freq/gain on channel %lu/%lu : BW %f (readback %f)\n",i,s->usrp->get_rx_num_channels(),openair0_cfg[0].rx_bw/1e6,s->usrp->get_rx_bandwidth(i)/1e6);
knopp's avatar
knopp committed
704
      s->usrp->set_rx_freq(openair0_cfg[0].rx_freq[i],i);
705
      set_rx_gain_offset(&openair0_cfg[0],i,bw_gain_adjust);
706 707 708 709 710 711 712 713 714 715 716 717

      ::uhd::gain_range_t gain_range = s->usrp->get_rx_gain_range(i);
      // limit to maximum gain
      if (openair0_cfg[0].rx_gain[i]-openair0_cfg[0].rx_gain_offset[i] > gain_range.stop()) {
	
        printf("RX Gain %lu too high, lower by %f dB\n",i,openair0_cfg[0].rx_gain[i]-openair0_cfg[0].rx_gain_offset[i] - gain_range.stop());
	exit(-1);
      }
      s->usrp->set_rx_gain(openair0_cfg[0].rx_gain[i]-openair0_cfg[0].rx_gain_offset[i],i);
      printf("RX Gain %lu %f (%f) => %f (max %f)\n",i,
	     openair0_cfg[0].rx_gain[i],openair0_cfg[0].rx_gain_offset[i],
	     openair0_cfg[0].rx_gain[i]-openair0_cfg[0].rx_gain_offset[i],gain_range.stop());
718 719
    }
  }
720
  for(i=0;i<s->usrp->get_tx_num_channels();i++) {
721
    if (i<openair0_cfg[0].tx_num_channels) {
knopp's avatar
knopp committed
722
      s->usrp->set_tx_rate(openair0_cfg[0].sample_rate,i);
723 724
      //s->usrp->set_tx_bandwidth(openair0_cfg[0].tx_bw,i);
      //printf("Setting tx freq/gain on channel %lu/%lu: BW %f (readback %f)\n",i,s->usrp->get_tx_num_channels(),openair0_cfg[0].tx_bw/1e6,s->usrp->get_tx_bandwidth(i)/1e6);
knopp's avatar
knopp committed
725 726
      s->usrp->set_tx_freq(openair0_cfg[0].tx_freq[i],i);
      s->usrp->set_tx_gain(openair0_cfg[0].tx_gain[i],i);
727 728
    }
  }
knopp's avatar
knopp committed
729 730


731 732
  // display USRP settings
  std::cout << boost::format("Actual master clock: %fMHz...") % (s->usrp->get_master_clock_rate()/1e6) << std::endl;
733 734
  
  sleep(1);
735 736

  // create tx & rx streamer
737
  uhd::stream_args_t stream_args_rx("sc16", "sc16");
738
  //stream_args_rx.args["spp"] = str(boost::format("%d") % 2048);//(openair0_cfg[0].rx_num_channels*openair0_cfg[0].samples_per_packet));
739
  for (i = 0; i<openair0_cfg[0].rx_num_channels; i++)
740 741 742 743 744 745 746
    stream_args_rx.channels.push_back(i);
  s->rx_stream = s->usrp->get_rx_stream(stream_args_rx);
  std::cout << boost::format("rx_max_num_samps %u") % (s->rx_stream->get_max_num_samps()) << std::endl;
  //openair0_cfg[0].samples_per_packet = s->rx_stream->get_max_num_samps();

  uhd::stream_args_t stream_args_tx("sc16", "sc16");
  //stream_args_tx.args["spp"] = str(boost::format("%d") % 2048);//(openair0_cfg[0].tx_num_channels*openair0_cfg[0].samples_per_packet));
747
  for (i = 0; i<openair0_cfg[0].tx_num_channels; i++)
748 749
      stream_args_tx.channels.push_back(i);
  s->tx_stream = s->usrp->get_tx_stream(stream_args_tx);
750 751
  std::cout << boost::format("tx_max_num_samps %u") % (s->tx_stream->get_max_num_samps()) << std::endl;

752

753 754 755 756 757
 /* Setting TX/RX BW after streamers are created due to USRP calibration issue */
  for(i=0;i<s->usrp->get_tx_num_channels();i++) {
    if (i<openair0_cfg[0].tx_num_channels) {
      s->usrp->set_tx_bandwidth(openair0_cfg[0].tx_bw,i);
      printf("Setting tx freq/gain on channel %lu/%lu: BW %f (readback %f)\n",i,s->usrp->get_tx_num_channels(),openair0_cfg[0].tx_bw/1e6,s->usrp->get_tx_bandwidth(i)/1e6);
Rohit Gupta's avatar
Rohit Gupta committed
758 759 760 761 762
    }
  }
  for(i=0;i<s->usrp->get_rx_num_channels();i++) {
    if (i<openair0_cfg[0].rx_num_channels) {
      s->usrp->set_rx_bandwidth(openair0_cfg[0].rx_bw,i);
763 764 765 766
      printf("Setting rx freq/gain on channel %lu/%lu : BW %f (readback %f)\n",i,s->usrp->get_rx_num_channels(),openair0_cfg[0].rx_bw/1e6,s->usrp->get_rx_bandwidth(i)/1e6);
    }
  }

767
  s->usrp->set_time_now(uhd::time_spec_t(0.0));
768
 
769

knopp's avatar
knopp committed
770 771
  for (i=0;i<openair0_cfg[0].rx_num_channels;i++) {
    if (i<openair0_cfg[0].rx_num_channels) {
772
      printf("RX Channel %lu\n",i);
knopp's avatar
knopp committed
773 774 775 776 777 778 779 780 781 782 783
      std::cout << boost::format("Actual RX sample rate: %fMSps...") % (s->usrp->get_rx_rate(i)/1e6) << std::endl;
      std::cout << boost::format("Actual RX frequency: %fGHz...") % (s->usrp->get_rx_freq(i)/1e9) << std::endl;
      std::cout << boost::format("Actual RX gain: %f...") % (s->usrp->get_rx_gain(i)) << std::endl;
      std::cout << boost::format("Actual RX bandwidth: %fM...") % (s->usrp->get_rx_bandwidth(i)/1e6) << std::endl;
      std::cout << boost::format("Actual RX antenna: %s...") % (s->usrp->get_rx_antenna(i)) << std::endl;
    }
  }

  for (i=0;i<openair0_cfg[0].tx_num_channels;i++) {

    if (i<openair0_cfg[0].tx_num_channels) { 
784
      printf("TX Channel %lu\n",i);
knopp's avatar
knopp committed
785 786 787 788 789 790 791 792
      std::cout << std::endl<<boost::format("Actual TX sample rate: %fMSps...") % (s->usrp->get_tx_rate(i)/1e6) << std::endl;
      std::cout << boost::format("Actual TX frequency: %fGHz...") % (s->usrp->get_tx_freq(i)/1e9) << std::endl;
      std::cout << boost::format("Actual TX gain: %f...") % (s->usrp->get_tx_gain(i)) << std::endl;
      std::cout << boost::format("Actual TX bandwidth: %fM...") % (s->usrp->get_tx_bandwidth(i)/1e6) << std::endl;
      std::cout << boost::format("Actual TX antenna: %s...") % (s->usrp->get_tx_antenna(i)) << std::endl;
    }
  }

793
  std::cout << boost::format("Device timestamp: %f...") % (s->usrp->get_time_now().get_real_secs()) << std::endl;
794 795 796 797

  device->priv = s;
  device->trx_start_func = trx_usrp_start;
  device->trx_write_func = trx_usrp_write;
798 799 800 801 802 803 804
  device->trx_read_func  = trx_usrp_read;
  device->trx_get_stats_func = trx_usrp_get_stats;
  device->trx_reset_stats_func = trx_usrp_reset_stats;
  device->trx_end_func   = trx_usrp_end;
  device->trx_stop_func  = trx_usrp_stop;
  device->trx_set_freq_func = trx_usrp_set_freq;
  device->trx_set_gains_func   = trx_usrp_set_gains;
805 806
  device->openair0_cfg = openair0_cfg;

knopp's avatar
knopp committed
807
  s->sample_rate = openair0_cfg[0].sample_rate;
808 809 810 811 812 813 814 815 816
  // TODO:
  // init tx_forward_nsamps based usrp_time_offset ex
  if(is_equal(s->sample_rate, (double)30.72e6))
    s->tx_forward_nsamps  = 176;
  if(is_equal(s->sample_rate, (double)15.36e6))
    s->tx_forward_nsamps = 90;
  if(is_equal(s->sample_rate, (double)7.68e6))
    s->tx_forward_nsamps = 50;
  return 0;
817
  }
818
}
819
/*@}*/