Commit 7ed4fa3e authored by Florian Kaltenberger's avatar Florian Kaltenberger

adapting lte-softmodem to new PCI interface

adding new target emos-raw


git-svn-id: http://svn.eurecom.fr/openair4G/trunk@4718 818b1a75-f10b-46b9-bf7c-635c3b92a50f
parent 3ddc05b3
......@@ -32,3 +32,4 @@ dot11:lxrt+sem+mbx+msg+fifos:!sudo ./dot11 -C 1907600000 -d;sleep 1;popall:contr
dot11_tx_test: lxrt+sem+mbx+msg+fifos:!sudo ./dot11 -C 1907600000 -d -t;sleep 1;popall:control_c
eNB2_750:lxrt+sem+mbx+msg+fifos:!sudo ./synctest_eNB -C 746000000 -F enb1tx_750 -d;sleep 1;popall:control_c
eNB2_1900:lxrt+sem+mbx+msg+fifos:!sudo ./synctest_eNB -C 19076000000 -F enb1tx_1900 -d;sleep 1;popall:control_c
emos-raw:lxrt+sem+mbx+msg+fifos:!sudo ./emos-raw -C 1907600000;sleep 1;popall:control_c
......@@ -249,6 +249,11 @@ lte-softmodem-usrp: $(OBJ) $(ASN1_MSG_OBJS1) $(RTAI_OBJ) $(USRP_OBJ) $(SHARED_DE
@echo Linking $@
@$(CC) $(USRP_OBJ) $(CFLAGS) $(OBJ) $(RTAI_OBJ) $(ASN1_MSG_OBJS1) -o lte-softmodem-usrp $(LDFLAGS) $(LIBS)
OBJ_EMOS = $(OPENAIR_TARGETS)/ARCH/EXMIMO/USERSPACE/LIB/openair0_lib.o rt_wrapper.o $(OPENAIR2_DIR)/UTIL/LOG/log.o $(OPENAIR2_DIR)/UTIL/LOG/vcd_signal_dumper.o
emos-raw: $(SHARED_DEPENDENCIES) $(OBJ_EMOS) emos-raw.c
@$(CC) $(CFLAGS) $(EXTRA_CFLAGS) $(RTAI_CFLAGS) $(OBJ_EMOS) -o emos-raw emos-raw.c $(LDFLAGS) $(LIBS)
synctest_eNB: synctest
cp synctest synctest_eNB
......
This diff is collapsed.
......@@ -16,20 +16,22 @@ if [ ! -e /dev/openair0 ]; then
fi
DEVICE=`echo $PCI | awk -F\" '{print $(NF-1)}' | awk '{print $2}'`
if [ $(($DEVICE%100)) == 8 ]; then
if [ $DEVICE == '2208' ]; then
echo "Using firmware version 8"
$OPENAIR_TARGETS/ARCH/EXMIMO/USERSPACE/OAI_FW_INIT/updatefw -s 0x43fffff0 -b -f $OPENAIR_TARGETS/ARCH/EXMIMO/USERSPACE/OAI_FW_INIT/sdr_expressmimo2
else
if [ $(($DEVICE%100)) == 9 ]; then
if [ $DEVICE == '2209' ]; then
echo "Using firmware version 9"
#$OPENAIR_TARGETS/ARCH/EXMIMO/USERSPACE/OAI_FW_INIT/updatefw -s 0x43fffff0 -b -f $OPENAIR0_DIR/express-mimo/software/sdr/exmimo2/sdr_expressmimo2
$OPENAIR_TARGETS/ARCH/EXMIMO/USERSPACE/OAI_FW_INIT/updatefw -s 0x43fffff0 -b -f $OPENAIR_TARGETS/ARCH/EXMIMO/USERSPACE/OAI_FW_INIT/sdr_expressmimo2_v9
else
if [ $(($DEVICE%100)) == 10 ]; then
$OPENAIR_TARGETS/ARCH/EXMIMO/USERSPACE/OAI_FW_INIT/updatefw -s 0x43fffff0 -b -f $OPENAIR_TARGETS/ARCH/EXMIMO/USERSPACE/OAI_FW_INIT/sdr_expressmimo2_v10
else
echo 'No corresponding firmware found'
return
if [ $DEVICE == '220a' ]; then
echo "Using firware version 10"
$OPENAIR_TARGETS/ARCH/EXMIMO/USERSPACE/OAI_FW_INIT/updatefw -s 0x43fffff0 -b -f $OPENAIR_TARGETS/ARCH/EXMIMO/USERSPACE/OAI_FW_INIT/sdr_expressmimo2_v10
else
echo 'No corresponding firmware found'
return
fi
fi
fi
......
......@@ -189,8 +189,8 @@ int otg_enabled;
#endif
int number_of_cards = 1;
//int mbox_bounds[20] = {8,16,24,30,38,46,54,60,68,76,84,90,98,106,114,120,128,136,144, 0}; ///boundaries of slots in terms ob mbox counter rounded up to even numbers
int mbox_bounds[20] = {6,14,22,28,36,44,52,58,66,74,82,88,96,104,112,118,126,134,142, 148}; ///boundaries of slots in terms ob mbox counter rounded up to even numbers
int mbox_bounds[20] = {8,16,24,30,38,46,54,60,68,76,84,90,98,106,114,120,128,136,144, 0}; ///boundaries of slots in terms ob mbox counter rounded up to even numbers
//int mbox_bounds[20] = {6,14,22,28,36,44,52,58,66,74,82,88,96,104,112,118,126,134,142, 148}; ///boundaries of slots in terms ob mbox counter rounded up to even numbers
int init_dlsch_threads(void);
void cleanup_dlsch_threads(void);
......@@ -1295,7 +1295,7 @@ int main(int argc, char **argv) {
}
else { //UE_flag==1
frame_parms->nb_antennas_tx = 1;
frame_parms->nb_antennas_rx = 2;
frame_parms->nb_antennas_rx = 1;
}
frame_parms->nb_antennas_tx_eNB = (transmission_mode == 1) ? 1 : 2; //initial value overwritten by initial sync later
frame_parms->mode1_flag = (transmission_mode == 1) ? 1 : 0;
......@@ -1472,7 +1472,7 @@ int main(int argc, char **argv) {
NB_INST=1;
openair_daq_vars.ue_dl_rb_alloc=0x1fff;
openair_daq_vars.target_ue_dl_mcs=0;
openair_daq_vars.target_ue_dl_mcs=20;
openair_daq_vars.ue_ul_nb_rb=6;
openair_daq_vars.target_ue_ul_mcs=6;
......@@ -1509,14 +1509,24 @@ int main(int argc, char **argv) {
printf("Card %d: ExpressMIMO %d, HW Rev %d, SW Rev 0x%d\n", card, p_exmimo_id->board_exmimoversion, p_exmimo_id->board_hwrev, p_exmimo_id->board_swrev);
if (p_exmimo_id->board_swrev>=BOARD_SWREV_CNTL2)
// check if the software matches firmware
if (p_exmimo_id->board_swrev!=BOARD_SWREV_CNTL2) {
printf("Software revision %d and firmware revision %d do not match. Please update either the firmware or the software!\n",BOARD_SWREV_CNTL2,p_exmimo_id->board_swrev);
exit(-1);
}
if (p_exmimo_id->board_swrev>=9)
p_exmimo_config->framing.eNB_flag = 0;
else
p_exmimo_config->framing.eNB_flag = !UE_flag;
p_exmimo_config->framing.tdd_config = DUPLEXMODE_FDD + TXRXSWITCH_LSB;
#ifdef PCIE_INTERFACE_V9
p_exmimo_config->framing.resampling_factor = 2;
#else
for (ant=0; ant<4; ant++)
p_exmimo_config->framing.resampling_factor[ant] = 2;
#endif
for (ant=0;ant<max(frame_parms->nb_antennas_tx,frame_parms->nb_antennas_rx);ant++)
p_exmimo_config->rf.rf_mode[ant] = rf_mode_base;
......@@ -1530,9 +1540,10 @@ int main(int argc, char **argv) {
}
/*
ant_offset = 3;
ant_offset = 0;
for (ant=0; ant<4; ant++) {
if (ant==ant_offset) {
//if (1) {
p_exmimo_config->rf.rf_mode[ant] = rf_mode_base;
p_exmimo_config->rf.rf_mode[ant] += (TXEN + DMAMODE_TX);
p_exmimo_config->rf.rf_mode[ant] += (RXEN + DMAMODE_RX);
......@@ -1927,8 +1938,12 @@ int main(int argc, char **argv) {
void test_config(int card, int ant, unsigned int rf_mode, int UE_flag) {
p_exmimo_config->framing.eNB_flag = !UE_flag;
p_exmimo_config->framing.tdd_config = 0;
#ifdef PCIE_INTERFACE_V9
p_exmimo_config->framing.resampling_factor = 2;
#else
p_exmimo_config->framing.resampling_factor[ant] = 2;
#endif
p_exmimo_config->rf.rf_freq_rx[ant] = 1907600000;
p_exmimo_config->rf.rf_freq_tx[ant] = 1907600000;;
p_exmimo_config->rf.rx_gain[ant][0] = 20;
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment