Commit 9eac7ac6 authored by gauthier's avatar gauthier

fixed TX/RX timing for B210 5 MHz

parent 37d7fa8d
......@@ -464,7 +464,7 @@ int openair0_dev_init_usrp(openair0_device* device, openair0_config_t *openair0_
break;
case 7680000:
openair0_cfg[0].samples_per_packet = 1024;
openair0_cfg[0].tx_sample_advance = 103;
openair0_cfg[0].tx_sample_advance = 70;//103;
openair0_cfg[0].tx_scheduling_advance = 5*openair0_cfg[0].samples_per_packet;
break;
case 1920000:
......@@ -479,13 +479,11 @@ int openair0_dev_init_usrp(openair0_device* device, openair0_config_t *openair0_
}
}
for(i=0;i<s->usrp->get_rx_num_channels();i++) {
if (i<openair0_cfg[0].rx_num_channels) {
s->usrp->set_rx_rate(openair0_cfg[0].sample_rate,i);
s->usrp->set_rx_bandwidth(openair0_cfg[0].rx_bw,i);
printf("Setting rx freq/gain on channel %lu/%lu\n",i,s->usrp->get_rx_num_channels());
printf("Setting rx freq/gain on channel %lu/%lu : BW %f (readback %f)\n",i,s->usrp->get_rx_num_channels(),openair0_cfg[0].rx_bw/1e6,s->usrp->get_rx_bandwidth(i)/1e6);
s->usrp->set_rx_freq(openair0_cfg[0].rx_freq[i],i);
set_rx_gain_offset(&openair0_cfg[0],i);
......@@ -506,7 +504,7 @@ int openair0_dev_init_usrp(openair0_device* device, openair0_config_t *openair0_
if (i<openair0_cfg[0].tx_num_channels) {
s->usrp->set_tx_rate(openair0_cfg[0].sample_rate,i);
s->usrp->set_tx_bandwidth(openair0_cfg[0].tx_bw,i);
printf("Setting tx freq/gain on channel %lu/%lu\n",i,s->usrp->get_tx_num_channels());
printf("Setting tx freq/gain on channel %lu/%lu: BW %f (readback %f)\n",i,s->usrp->get_tx_num_channels(),openair0_cfg[0].tx_bw/1e6,s->usrp->get_tx_bandwidth(i)/1e6);
s->usrp->set_tx_freq(openair0_cfg[0].tx_freq[i],i);
s->usrp->set_tx_gain(openair0_cfg[0].tx_gain[i],i);
}
......
......@@ -36,7 +36,7 @@ eNBs =
nb_antennas_tx = 1;
nb_antennas_rx = 1;
tx_gain = 90;
rx_gain = 120;
rx_gain = 132;
prach_root = 0;
prach_config_index = 0;
prach_high_speed = "DISABLE";
......@@ -143,10 +143,10 @@ eNBs =
NETWORK_INTERFACES :
{
ENB_INTERFACE_NAME_FOR_S1_MME = "eth0";
ENB_IPV4_ADDRESS_FOR_S1_MME = "192.168.12.216/24";
ENB_IPV4_ADDRESS_FOR_S1_MME = "192.168.12.213/24";
ENB_INTERFACE_NAME_FOR_S1U = "eth0";
ENB_IPV4_ADDRESS_FOR_S1U = "192.168.12.216/24";
ENB_IPV4_ADDRESS_FOR_S1U = "192.168.12.213/24";
ENB_PORT_FOR_S1U = 2152; # Spec 2152
};
......
......@@ -132,7 +132,7 @@ eNBs =
};
////////// MME parameters:
mme_ip_address = ( { ipv4 = "192.168.13.11";
mme_ip_address = ( { ipv4 = "192.168.12.11";
ipv6 = "192:168:30::17";
active = "yes";
preference = "ipv4";
......@@ -142,10 +142,10 @@ eNBs =
NETWORK_INTERFACES :
{
ENB_INTERFACE_NAME_FOR_S1_MME = "eth0";
ENB_IPV4_ADDRESS_FOR_S1_MME = "192.168.13.10/24";
ENB_IPV4_ADDRESS_FOR_S1_MME = "192.168.12.213/24";
ENB_INTERFACE_NAME_FOR_S1U = "eth0";
ENB_IPV4_ADDRESS_FOR_S1U = "192.168.13.10/24";
ENB_IPV4_ADDRESS_FOR_S1U = "192.168.12.213/24";
ENB_PORT_FOR_S1U = 2152; # Spec 2152
};
......
......@@ -2854,8 +2854,8 @@ int main( int argc, char **argv )
} else if (frame_parms[0]->N_RB_DL == 25) {
openair0_cfg[card].sample_rate=7.68e6;
openair0_cfg[card].samples_per_frame = 76800;
openair0_cfg[card].tx_bw = 2.5e6;
openair0_cfg[card].rx_bw = 2.5e6;
openair0_cfg[card].tx_bw = 5e6;
openair0_cfg[card].rx_bw = 5e6;
} else if (frame_parms[0]->N_RB_DL == 6) {
openair0_cfg[card].sample_rate=1.92e6;
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment