# -------- Local ---------
# The first parameter in this section is Identity, which will be used to 
# identify this peer in the Diameter network. The Diameter protocol mandates 
# that the Identity used is a valid FQDN for the peer. This parameter can be 
# omitted, in that case the framework will attempt to use system default value 
# (as returned by hostname --fqdn). 
Identity = "hss.openair4G.eur";

# In Diameter, all peers also belong to a Realm. If the realm is not specified,
# the framework uses the part of the Identity after the first dot.
Realm = "openair4G.eur";


# This parameter is mandatory, even if it is possible to disable TLS for peers 
# connections. A valid certificate for this Diameter Identity is expected. 
TLS_Cred = "/usr/local/etc/oai/freeDiameter/hss.cert.pem", "/usr/local/etc/oai/freeDiameter/hss.key.pem";
TLS_CA = "/usr/local/etc/oai/freeDiameter/hss.cacert.pem";


# Disable use of TCP protocol (only listen and connect in SCTP)
# Default : TCP enabled
No_SCTP;


# This option is ignored if freeDiameter is compiled with DISABLE_SCTP option.
# Prefer TCP instead of SCTP for establishing new connections.
# This setting may be overwritten per peer in peer configuration blocs.
# Default : SCTP is attempted first.
Prefer_TCP;


# Disable use of IPv6 addresses (only IP)
# Default : IPv6 enabled
No_IPv6;


# Overwrite the number of SCTP streams. This value should be kept low, 
# especially if you are using TLS over SCTP, because it consumes a lot of 
# resources in that case. See tickets 19 and 27 for some additional details on 
# this.
# Limit the number of SCTP streams
SCTP_streams = 3;


# By default, freeDiameter acts as a Diameter Relay Agent by forwarding all 
# messages it cannot handle locally. This parameter disables this behavior.
NoRelay;


# Use RFC3588 method for TLS protection, where TLS is negociated after CER/CEA exchange is completed
# on the unsecure connection. The alternative is RFC6733 mechanism, where TLS protects also the
# CER/CEA exchange on a dedicated secure port.
# This parameter only affects outgoing connections.
# The setting can be also defined per-peer (see Peers configuration section).
# Default: use RFC6733 method with separate port for TLS.

#TLS_old_method;


# Number of parallel threads that will handle incoming application messages. 
# This parameter may be deprecated later in favor of a dynamic number of threads
# depending on the load. 
AppServThreads = 4;

# Specify the addresses on which to bind the listening server. This must be 
# specified if the framework is unable to auto-detect these addresses, or if the
# auto-detected values are incorrect. Note that the list of addresses is sent 
# in CER or CEA message, so one should pay attention to this parameter if some 
# adresses should be kept hidden. 
#ListenOn = "127.0.0.1";

Port = 3868;
SecPort = 5868;

# -------- Extensions ---------

# Uncomment (and create rtd.conf) to specify routing table for this peer.
#LoadExtension = "rt_default.fdx" : "rtd.conf";

# Uncomment (and create acl.conf) to allow incoming connections from other peers.
LoadExtension = "acl_wl.fdx" : "/usr/local/etc/oai/freeDiameter/acl.conf";

# Uncomment to display periodic state information
#LoadExtension = "dbg_monitor.fdx";

# Uncomment to enable an interactive Python interpreter session.
# (see doc/dbg_interactive.py.sample for more information)
#LoadExtension = "dbg_interactive.fdx";

# Load the RFC4005 dictionary objects
#LoadExtension = "dict_nasreq.fdx";

LoadExtension = "dict_nas_mipv6.fdx";
LoadExtension = "dict_s6a.fdx";

# Load RFC4072 dictionary objects
#LoadExtension = "dict_eap.fdx";

# Load the Diameter EAP server extension (requires diameap.conf)
#LoadExtension = "app_diameap.fdx" : "diameap.conf";

# Load the Accounting Server extension (requires app_acct.conf)
#LoadExtension = "app_acct.fdx" : "app_acct.conf";

# -------- Peers ---------

# The framework will actively attempt to establish and maintain a connection
# with the peers listed here.
# For only accepting incoming connections, see the acl_wl.fx extension.

#ConnectPeer = "ubuntu.localdomain" { ConnectTo = "127.0.0.1"; No_TLS; };