This bug happens when we detect uplink failure for one UE.
In this case, a DCI format 1A is sent to the UE to ask it
to do random acces.

The way this DCI is generated was not compatible with how
the software is organized. It was expected that the DCI are
added (with add_ue_spec_dci and add_common_dci) in a very
specific order: first all DCIs in common space are added
(with add_common_dci) then all DCIs in UE specific space
are added (with add_ue_spec_dci).

The problem was that the DCI format 1A DCI sent to the UE
for it to do random access is added (with add_ue_spec_dci)
before the DCIs in common space.

That totally messed up the logic in add_common_dci and
add_ue_spec_dci.

The solution is to get rid of Num_common_dci and Num_ue_spec_dci,
replace those two counters by only one (Num_dci) and add
"search_space" in the dci_alloc structure to be used later by
the function "allocate_CCEs" when calling "get_nCCE_offset".

The software had to be adapted to the new variables, everywhere.

I am not sure that the simulators work. It seems that some
of them didn't use Num_common_dci and Num_ue_spec_dci to
decide on what space (common or UE specific) to put the DCI,
but relied on the rnti (comparing with SI_RNTI). To be tested
properly.

The modified simulators are:
  - openair1/SIMULATION/LTE_PHY/dlsim.c
  - openair1/SIMULATION/LTE_PHY/dlsim_tm4.c
  - openair1/SIMULATION/LTE_PHY/dlsim_tm7.c
  - openair1/SIMULATION/LTE_PHY/framegen.c
  - openair1/SIMULATION/LTE_PHY/pdcchsim.c
  - openair1/SIMULATION/LTE_PHY/syncsim.c

develop_integration_w25 into develop

Summary of changes:
- UE: configurable thread
- UE: fix in dci format1c decoding
- bladeRF hack
- configuration files for oaisim

See merge request !209

changes:
- ue mcc/mnc 208.93
- use correct key/opc for user
- change addresses in conf file for them to be easier to understand
  (maybe)

With those changes, running:
   sudo ./run_enb_ue_virt_s1
in cmake_targets/tools should work out of the box

The user still has to configure correct IP addresses in
targets/PROJECTS/GENERIC-LTE-EPC/CONF/enb.band7.generic.oaisim.local_mme.conf

We supposed oaisim (enb+ue) machine to be on IP address 10.0.1.1
and EPC (hss, mme, spgw) machine to be on IP address 10.0.1.2.

Several problems are present.

The first is that _write returns 0 instead of the
number of samples. We solve it by returning
nsamps.

The second is that _read may return less samples at
the beginning and we don't want to exit for that.
We solve it also by returning nsamps.
(We still need to log more in this, to be done in the
next commit.)

The third is that after initialization we don't send
anything for a while, time for the softmodem to finish
its init. This generates lots of "RX overrun".
We solve it by disabling TX and RX modules after init
and then in trx_brf_start we activate them again (and
also call bladerf_sync_config, which seems to be
mandatory, and bladerf_calibrate_dc, which may be avoided,
perhaps).

Maybe not the end of the story. Sometimes it works, UE connects,
traffic is fine (tested only with 5MHz). Sometimes it does not,
UE does not connect, or it connects but then traffic is bad,
especially uplink.

To be refined.

develop_integration_w24 into develop

Summary or changes:
- work on transmission mode 3 and 4

See merge request !204

only with XFORMS enabled.

The way it was done was confusing.
However, now rank adaptation (if enabled) is not visualized correctly.