Some computation has been fixed in PUCCH reception.

SNR has been fixed, uses measurement instead of
a fixed value for the noise.

normalized_rx_power and target_rx_power have been removed,
replaced by snr and target_snr. All the files using those
variables have been updated.

CI: adding support to repeat scenario in case of failure.

See merge request oai/openairinterface5g!645

    nice when the tested feature is known to be unstable
    CDRX testing is now separated from normal FDD 10MHz testing

Signed-off-by: Raphael Defosseux <raphael.defosseux@eurecom.fr>

CI:  Downgrade cdrx testing

See merge request oai/openairinterface5g!643

Signed-off-by: Raphael Defosseux <raphael.defosseux@eurecom.fr>

Signed-off-by: Raphael Defosseux <raphael.defosseux@eurecom.fr>

Signed-off-by: Raphael Defosseux <raphael.defosseux@eurecom.fr>

Signed-off-by: Raphael Defosseux <raphael.defosseux@eurecom.fr>

Signed-off-by: Raphael Defosseux <raphael.defosseux@eurecom.fr>

develop integration branch: 2019 week 28

See merge request oai/openairinterface5g!640

* MR 635 : fix rfsim ue sync
* MR 636 : Bugfixes 2019 w28
* MR 637 : Fixing Multi-RRU support and CI Testing
* MR 639 : fix bladeRF compilation

Merge remote-tracking branch 'origin/ci-develop-multi-rru-support' into develop_integration_2019_w28

Signed-off-by: Raphael Defosseux <raphael.defosseux@eurecom.fr>

Signed-off-by: Raphael Defosseux <raphael.defosseux@eurecom.fr>

Signed-off-by: Raphael Defosseux <raphael.defosseux@eurecom.fr>

The 5G phone OPPO has a very big UE capability (> 2KB).

We need bigger buffers to transfer this, especially in x2 handover.

Also the sctp messages need a bigger buffer.

Note: in sctp, we didn't check for partial messages, it's now
      done. When detected, we exit. To be redone differently
      if needed. (Look for "if (!(flags & MSG_EOR))".)

We declare variables in header files, we don't define them. So we need
to use 'extern' in the header file and put the definition
in some C file.

This used to be done to ease power estimation in the UE,
but this is not correct. Let's put no energy in the REs
with no DCI data, which is what needs to be done.

Plus it consumes a lot of CPU because of calling taus()
way too much.

To be used when you send data to another host.

On the other host, to avoid ICMP traffic about the port
not being open, do:

./nc -l -u -p 9999 > /dev/null

You need to restart this command each time you run macpdu2wireshark.
You can use any other program that will accept UDP packets on the
port 9999 (default port of macpdu2wireshark, change if you use another
port of course).

Signed-off-by: Raphael Defosseux <raphael.defosseux@eurecom.fr>

Signed-off-by: Raphael Defosseux <raphael.defosseux@eurecom.fr>

Signed-off-by: Raphael Defosseux <raphael.defosseux@eurecom.fr>

Develop: Integration 2019 Week 27

See merge request oai/openairinterface5g!629

Signed-off-by: Raphael Defosseux <raphael.defosseux@eurecom.fr>

Signed-off-by: Raphael Defosseux <raphael.defosseux@eurecom.fr>

Fix a few cppcheck errors/warnings

Signed-off-by: Raphael Defosseux <raphael.defosseux@eurecom.fr>

The value was set to 20 which means -120 dB. Setting this value means
that the UE reports an event only if the RSRP of the serving cell
is lower than -120 dB.

In the lab, we get values of around -70, and to go as low as -120
means a very degraded environment. This is not practical.

Let's disactivate the setting of this parameter for the moment so that
the UE reports an event without taking into consideration the RSRP
of the serving cell.

With this hotfix, the X2 handover works much better.

Signed-off-by: Raphael Defosseux <raphael.defosseux@eurecom.fr>

Merge remote-tracking branch 'origin/flexran_agent_rrc_cm_rebased2' into develop_integration_2019_w27